reduction ratio

reduction ratio的基本解释

-

减速比

与reduction ratio相关的网络例句 [注：此内容来源于网络，仅供参考]

The sulfate-reducing-bacteria were immobilized in polyvinyl alcohol to treat wastewater containing zinc. The effects of different crosslinking reagents on the conglobation, cohered efficiency of the carbon source, reduction ratio of sulfate, removal ratio of Zn, and COD of drainage were considered.

摘 要：以聚乙烯醇为包埋介质，对硫酸盐还原菌进行固定化处理；以含锌废水为处理对象，考察不同交联剂对成球性能影响、营养源内聚效果、硫酸盐还原效果、锌离子去除率和出水COD等因素。

NO_x decreasing ratio of micronized coal reburning comparing withgeneral combustion is not proportionable to NO_x reduction ratio in reduction zone,which depends on both NO_x reduction ratio and NO_x increment in burnout zone.

超细粉再燃与常规燃烧相比NO_x脱除率与再燃区NO_x还原率不成正比，它是由NO_x还原率与燃尽区NO_x新的生成综合决定的。

The experiment and the research indicate that:(1) Through the Hot-Continuous-Rolling production technics under small reduction ratio of 4.04 and 5.08, the rectangular continuous-casting billet of 235×265mm can be used to produce big size steel stick of Φ140mm and Φ 125mm whose macrostructure and mechanical properties meet the standards, this technics is viable;(2) This rolling technics can make the deformation penetrate to the center of the billet by low temperture and low velocity and big roller diameter and large reduction quantity at every pass and optimum design and arrangement of rollers, which is the key of Hot-Continuous-Rolling technics under small reduction ratio;(3) The sending technics used in Xining Special Steel Co.,Ltd can not use waste-heat of billet adequately, but the sensitive temperature section of A1N or sulphides or inclusions separating out is avoided, creating a favorablecondition for insuring good surface quality of final rolled steel;(4) The Hot-Continuous-Rolling technics under small reduction ratio has a close relationship with the billet quality control and the hot sending process control and the cooling control after rolling.

通过实验研究表明：(1) 235×265mm矩形连铸坯分别采用4.04和5.08的小压缩比热连轧生产工艺，所生产的Φ140mm和Φ125mm的大规格棒材，其低倍组织和机械性能均符合标准要求，该工艺是可行的；(2)本实验所采取的低温低速、大辊径大道次压下量轧制工艺加上轧辊孔型的优化设计与配置，可以使加工变形渗透到铸坯的中心，这一点是实现小压缩比热连轧生产工艺的关键；(3)西宁特钢在红送过程中虽然铸坯余热未能得到充分的利用，但是有效地避开了A1N、硫化物的析出及夹杂物偏析的敏感温度区，为保证最终轧材良好的表面质量创造了有利的条件；(4)小压缩比热连轧生产与铸坯质量控制，热送过程控制以及轧后冷却控制密不可分。

与reduction ratio相关的网络解释 [注：此内容来源于网络，仅供参考]

reduction ratio：破碎比

扁平指数使用如图1所示的扁平筛,通过矶磨耗损失是粗粒料坚韧性(toughness)的重要指标,与粗粒料抗破碎性能有良好的相关性,也因太过简化,使碎石成品的破碎比(Reduction Ratio)过大,造成扁长颗粒较多.为达到SMA根据ASTM D242-95之定义,

reduction ratio：减速比

reduction gyratory crusher 碎减式旋回破碎机 | reduction ratio 减速比 | reed 导火线

reduction ratio：缩小比(减压比)

行程损失 loss of travel | 缩小比(减压比) reduction ratio | 回缩 retraction