英语人>词典>英汉 : quiescent time的中文,翻译,解释,例句
quiescent time的中文,翻译,解释,例句

quiescent time

quiescent time的基本解释
-

停止时间

更多网络例句与quiescent time相关的网络例句 [注:此内容来源于网络,仅供参考]

Cyclopentane reduced the induction time of hydrate formation, but could not improve the methane consumption during gas hydrate formation in a quiescent cell.

液态烃环戊烷降低了水合物形成的诱导时间,但环戊烷不能提高水合物的填充密度。

The effects of the amount of sulfuric acid solution,the amount of potassium iodide solution and quiescent time after extraction were investigated.

考察了硫酸溶液的用量、碘化钾溶液的用量及萃取后静置时间等条件对双氧水含量分析的影响。

The results show that the plasticity zone and dynamically quiescent layer become fine equiaxed recrystallisation under the thermo-mechanical effect, the grains in the heat-affected zone grow up because of the effect of friction heat. When the rotation speed is 2 500 r/min and the welding time is 12 s, good joint is achieved, and the tensile shear strength of the joint reaches 9.24 kN. The tensile shear strength of spot increases with increasing tool rotation speed, with increasing welding time, the strength increases first, while then reduces. The microhardness of plasticity zone is high, but is slightly lower than that of the base metal, the minimum value of microhardness is in the heat affected zone. When the energy input of joint is high, the fracture type of spot is mode Ⅰ, and the tensile shear strength is high; on the contrary, when the energy input of joint is less the fracture type of spot is mode Ⅱ, and the strength is low.

结果表明:塑性区和动态静止层的晶粒在热和力作用下发生动态再结晶形成细小的等轴晶,热影响区的晶粒在摩擦热作用下长大变粗;搅拌头旋转速度为2 500 r/min,焊接时间为12 s时,可以获得力学性能较好的焊点,焊点的剪切强度达到9.24 kN;焊点的剪切强度随搅拌头旋转速度的增大而增大,随焊接时间的延长先增大后减小;塑性区的显微硬度较高,但略小于母材,接头显微硬度的最小值分布在热影响区;焊点热输入量较多时,接头为Ⅰ型断裂,焊点的剪切强度较高;焊点热输入量较少时,接头为Ⅱ型断裂,焊点的强度较低。

更多网络解释与quiescent time相关的网络解释 [注:此内容来源于网络,仅供参考]

quiescent:静止的

quiescent time 静止时间 | quiescent 静止的 | quiet automatic gain control 无噪声自动增益控制

quick turnaround time:短设计 生产周期

quick setup 快速蝶 | quick turnaround time 短设计 生产周期 | quiescent point 静点

quick turnaround time:短设计 生产周期APU中国学习动力网

quick setup 快速蝶APU中国学习动力网 | quick turnaround time 短设计 生产周期APU中国学习动力网 | quiescent point 静点APU中国学习动力网