pulley spindle
- pulley spindle的基本解释
-
-
滑轮轴, 滑车轴
- 更多网络例句与pulley spindle相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The use of pre-used triangular belt transmission, the power machine spindle and pumps must be parallel to pulley alignment, in which the center distance of not less than the diameter of the pulley and two double.
使用前的准备①采用三角皮带传动时，动力机主轴和水泵必须平行，皮带轮要对齐，其中中心距不得小于两皮带轮直径之和的两倍。
-
The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.
本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。
-
Key parts are imported directly from overseas which are advanced and reliable* Integral casting machine body to ensure high rigidity and stability* Precision processed working table with hard chrome-plated surface prolong the life time of the machine* Japan made MIKI PULLEY an infinitely speed adjuster with 6 - 25m/min infeed speed* Fully automated for entire infeed process* Each high precision spindle is supported by two bearings which makes spindle more stable.
配备有HFB523设备的经济型机械，但是消耗了更少的电压。*关键部件直接从海外进口，先进可靠。*机身整体铸件，保证高坚韧度和稳定性。*精加工工作台表面镀硬铬合金，能延长机器的使用寿命。*日本制造MIKI PULLEY，带6―25m/min的进给速度的一款无限速度调节器。*整个进给程序完全自动化。*每个高精度的轴都由两个轴承支持，使轴更稳定。
- 更多网络解释与pulley spindle相关的网络解释 [注：此内容来源于网络，仅供参考]
-
pulley stile：滑车槽,提拉窗滑车槽,吊窗滑车槽
pulley spindle ==> 滑轮轴 | pulley stile ==> 滑车槽,提拉窗滑车槽,吊窗滑车槽 | pulley support ==> 皮带轮支架
-
0ne 42" Star Hole Blade Included, Belt Pulley not Included 0ne：42 "星洞,包括叶片,皮带轮未列入
Spindle Can Fit Both 38" & 42" Cut Decks主轴... | 0ne 42" Star Hole Blade Included, Belt Pulley not Included 0ne 42 "星洞,包括叶片,皮带轮未列入 | (note) This is not an original Patended MTD part. (注) ...
-
pulley speed：皮带轮转速
pulley shell ==> 皮带轮罩 | pulley speed ==> 皮带轮转速 | pulley spindle ==> 滑轮轴