projective coordinates

projective coordinates的基本解释

-

射影坐标

与projective coordinates相关的网络例句 [注：此内容来源于网络，仅供参考]

The element equations are derived in a fixed current element coordinates which are coincident with the current moving element coordinates. The perturbed moving element coordinates and the variation of the element nodal rotation parameters corresponding to the perturbation of element nodal displacements and rotations referred to the current fixed element coordinates is consistently determined using the first order linearization of the way used to determine the current element coordinates and element nodal rotation parameters corresponding to the incremental element nodal displacements and rotations referred to the global coordinates.

本研究在梁元素当前的变形位置上，利用元素节点的座标及断面方位建立一个移动元素座标并决定元素节点的旋转参数，对应於元素节点旋转参数扰动量的广义节点力为一广义力矩，为推导传统力和力矩与该广义力矩的关系，本研究在一个与当前的移动元素座标重合的固定元素座标上，推导出元素节点在当前固定元素座标的扰动位移和扰动旋转与元素节点旋转参数的扰动量的关系。

In the first part, depending on three or more images, the main research work are listed as follows:(1) using SVD decomposition to realize projective reconstruction;(2) realizing camera self-calibration by solving Kruppa's equation;(3) recovering Euclidean reconstruction from projective reconstruction. Depending on only two images, the main researches are:(1) making out infinite plane homography matrix by using scene structure information, then recovering affine reconstruction from projective reconstruction;(2) making out the absolute conic images by using scene structure information, and then recovering Euclidean reconstruction from projective reconstruction.

在第一部分中，针对三幅及三幅以上的图像，主要研究：①利用矩阵奇异值分解实现射影重构，②通过求解Kruppa方程实现摄像机自标定，③由射影重构恢复欧氏重构；针对只有两幅图像的情况，主要研究：①利用场景结构信息求解无穷远平面的单应矩阵，由射影重构恢复仿射重构，②利用场景结构信息求解绝对二次曲线的像，由仿射重构恢复欧氏重构。

The paper puts forth that the numerical model of actual forming part is reconstructed by RE and the surface is regarded as actual trimmed surface, then grids and nodes mapping relationship between design model and actual forming part is acquired through compelling deformation simulation, and the design trimming line is dispersed into points according to a certain precision and the projective points and the coordinate values of the intersection points of projective line on the grids formed by discrete points are calculated along trimming direction, the new coordinate values of projective points and intersection points of projective line after deformation are calculated based on the mapping relationship of grids and nodes, the deformed trimming line can be acquired through fitting the points into curve.

本文提出通过逆向工程技术重构出实际冲压件的型面并以此型面为修边后实际冲压件的型面，然后采用强制变形仿真的方法建立设计模型和实际冲压件重构模型的网格和节点映射关系。将设计修边线按一定精度离散成点，然后根据修边方向计算出各点在网格上形成的投影点和投影线交点，根据之前计算出来的网格和节点映射关系就可以计算出投影点和投影线交点在变形后的新坐标，将其拟合成曲线就可以得到变形后修边线的形状。

与projective coordinates相关的网络解释 [注：此内容来源于网络，仅供参考]

projective coordinates：射影坐标

projective coordinate system 射影坐标系 | projective coordinates 射影坐标 | projective cover 射影覆盖

projective coordinates：射影座標

projective coordinate system 射影坐标系 | projective coordinates 射影座標 | projective correspondence 射影对应

projective coordinates system：射影坐标系

射影坐标 projective coordinates | 射影坐标系 projective coordinates system | 射影对应 projective correspondence