projective cone

projective cone的基本解释

-

射影锥

与projective cone相关的网络例句 [注：此内容来源于网络，仅供参考]

In the first part, depending on three or more images, the main research work are listed as follows:(1) using SVD decomposition to realize projective reconstruction;(2) realizing camera self-calibration by solving Kruppa's equation;(3) recovering Euclidean reconstruction from projective reconstruction. Depending on only two images, the main researches are:(1) making out infinite plane homography matrix by using scene structure information, then recovering affine reconstruction from projective reconstruction;(2) making out the absolute conic images by using scene structure information, and then recovering Euclidean reconstruction from projective reconstruction.

在第一部分中，针对三幅及三幅以上的图像，主要研究：①利用矩阵奇异值分解实现射影重构，②通过求解Kruppa方程实现摄像机自标定，③由射影重构恢复欧氏重构；针对只有两幅图像的情况，主要研究：①利用场景结构信息求解无穷远平面的单应矩阵，由射影重构恢复仿射重构，②利用场景结构信息求解绝对二次曲线的像，由仿射重构恢复欧氏重构。

The paper puts forth that the numerical model of actual forming part is reconstructed by RE and the surface is regarded as actual trimmed surface, then grids and nodes mapping relationship between design model and actual forming part is acquired through compelling deformation simulation, and the design trimming line is dispersed into points according to a certain precision and the projective points and the coordinate values of the intersection points of projective line on the grids formed by discrete points are calculated along trimming direction, the new coordinate values of projective points and intersection points of projective line after deformation are calculated based on the mapping relationship of grids and nodes, the deformed trimming line can be acquired through fitting the points into curve.

本文提出通过逆向工程技术重构出实际冲压件的型面并以此型面为修边后实际冲压件的型面，然后采用强制变形仿真的方法建立设计模型和实际冲压件重构模型的网格和节点映射关系。将设计修边线按一定精度离散成点，然后根据修边方向计算出各点在网格上形成的投影点和投影线交点，根据之前计算出来的网格和节点映射关系就可以计算出投影点和投影线交点在变形后的新坐标，将其拟合成曲线就可以得到变形后修边线的形状。

Test and analysis show that, the distribution patterns of the tangent veloctiy fields in the big cone area and the small cone area, which are comprised of para-free vortex and para-forced vortex, are basically identical without a change of the radius of the boundary surface; with the increase of the angle of the small cone, the para-free vortex area decreases and the para-forced vortex area increases, and the emulsifiability of the fluid drips increases with the increase of velocity gradient; the tangent velocity increases with the increase of inlet flow, and the maximum tangent velocities of both the big cone area and the small cone area are 4.94 times of the inlet flow; and the maximum tangent velocity increases with the increase of the split ratio and with the radius of the boundary surface not changed.

试验分析表明，大锥段和小锥段切向速度分布规律基本相同，均由准自由涡和准强制涡构成，分界面半径rm没有变化；随着小锥角θ的增加，准自由涡区缩小，准强制涡区扩大，速度梯度增加会加大液滴的乳化程度；随入口流量增加，切向速度增大，经拟合得出大锥段和小锥段的最大切向速度均为入口流量的4.94倍；分流比加大，分界面半径基本不变，最大切向速度增加。

与projective cone相关的网络解释 [注：此内容来源于网络，仅供参考]

projective cone：射影锥

kneeguard 护膝(装置) | projective cone 射影锥 | superheater header support 过热箱支座