pouring ['pɔ:riŋ]

pouring的基本解释

-

[变形] pour的现在分词

-

[机] 浇铸, 浇注

pouring的同义词

v. pour · stream

与pouring相关的网络例句 [注：此内容来源于网络，仅供参考]

One cycle of operation to take Silo body construction, the construction procedure as follows: steel banding to Silo body gantry beams assembled below -→ one-time pouring concrete 700mm high -→ early slide three trips (that is 75mm high)-→ check off the concrete slipform system appropriate degree and working conditions -→ continue pouring concrete 500mm high -→ then slip trip or three -→ pouring concrete to template missing -→ normal sliding each slide or 500mm high -→ stratified cross - lap steel banding -→ pouring concrete 500mm high -→ Waterloo or 500mm high -→ 4 in accordance with the procedure after Silo body pouring until the completion of cycle.

其中筒身施工采取循环作业，其施工程序为：绑扎筒身钢筋至组装好的门架横梁下面—→一次性浇筑混凝土700mm 高—→初滑三个行程（即75mm 高度）—→检查滑出混凝土合适度及滑模系统工作状况—→继续浇筑混凝土500mm 高—→再滑升三个行程—→浇筑混凝土至模板上口—→转入正常滑升，每次滑升500mm 高—→分层交圈绑扎钢筋—→浇筑混凝土500mm 高—→滑升500mm 高—→按后四道程序循环往复直至筒身浇筑完成。

One cycle of operation to take construction, the construction procedure as follows: steel banding to gantry beams assembled below -→ one-time pouring concrete 700mm high -→ early slide three trips (that is 75mm high)-→ check off the concrete slipform system appropriate degree and working conditions -→ continue pouring concrete 500mm high -→ then slip trip or three -→ pouring concrete to template missing -→ normal sliding each slide or 500mm high -→ stratified cross - lap steel banding -→ pouring concrete 500mm high -→ Waterloo or 500mm high -→ 4 in accordance with the procedure after pouring until the completion of cycle.

其中筒身施工采取循环作业，其施工程序为：绑扎筒身钢筋至组装好的门架横梁下面—→一次性浇筑混凝土700mm 高—→初滑三个行程（即75mm 高度）—→检查滑出混凝土合适度及滑模系统工作状况—→继续浇筑混凝土500mm 高—→再滑升三个行程—→浇筑混凝土至模板上口—→转入正常滑升，每次滑升500mm 高—→分层交圈绑扎钢筋—→浇筑混凝土500mm 高—→滑升500mm 高—→按后四道程序循环往复直至筒身浇筑完成。

When the pouring temperature is close to the liquidus temperature of AlSi7Mgalloy, the primary α-Alin the billets of AlSi7Mg alloy solidifies into spherical or nodular grainswhich are small and distributed homogeneously. In order to obtain non-dendritic semi-solidbillets,the appropriate pouring temperature is 615℃. The faster cooling rate,the melt flowing and largersolidification region induced by the near liquidus pouring temperature promotes theformation of spherical or nodular primary α-Al.

实验表明：当浇注温度接近液相线温度时，AlSi7Mg合金中的初生α-Al凝固成球状或粒状，晶粒细小，分布均匀；获得球状或粒状AlSi7Mg合金半固态坯料的最佳浇注温度为615℃；在接近液相线温度下浇注，较快的合金熔体冷却速度、浇注引起的合金熔体活动和大范围的同时凝固促使AlSi7Mg合金形成球状或粒状的初生α-Al组织。

与pouring相关的网络解释 [注：此内容来源于网络，仅供参考]

pouring：浇注

对粘合体的密着性和粘着性优秀,粘合体的移动(move-ment)或在外部应力的负荷状态下,附着性也很优秀. . 沥青间的相互亲和力强,可以用重叠涂装(multi plycoating),浇注(pouring)及投掷(putting)等方法来自由形成厚涂膜(最大3㎜).

pouring：浇铸,浇注

浇铸(浇钢锭) teeming | 浇铸,浇注 pouring | 浇铸不到(铸疵) short run

pouring：浇铸

pouring 倒出灌注 | pouring 浇铸 | powder box 火药箱

pouring：倒出灌注

pouring 倒出 | pouring 倒出灌注 | pouring 浇铸

pouring measure：量酒器

cocktail shaker 调酒器 | pouring measure 量酒器 | juice extractor 果汁榨汁机