plate metals

plate metals的基本解释

-

金属板

与plate metals相关的网络例句 [注：此内容来源于网络，仅供参考]

The furnace body is made ф2200×1500 the outer covering main body by the 12mm steel plate, lower part the furnace body 45° the installment has the sensor, the sensor orientation silicon steel plate is made the weight 2 ton induction iron cores by Wuhan Steel Corporation Silicon steel plate Factory production top gear's W-151 the cold rolling 0.35m/m, primary is made the water cooling coil by 10×10×2 the copper pipe, and installs the stainless steel water cooling restricting, the power frequency has the core smelting furnace's metal melt fluid namely for the sensor sencondary coil, the entire electric stove is a transformer actually, the necessary 6 grades from the pair regulating transformer, shift gears by the electricity cabinet control, the voltage may from low to high, divide 6 promotions to arrive at 380V, each grade of voltages are different, the output is also different, the furnace temperature along with the files position is also different, but the height is different, adapts smelts colored or the black and so on melting point different metals, and may make the new furnace lining to smelt diamantine drying furnace fireproof.

炉体由12mm钢板制成Ф2200×1500外壳主体，炉体下部45°安装有感应器，感应器由武钢硅钢片厂生产的最高档的W-151冷轧0.35m/m取向硅钢片制成重2吨感应铁心，初级由10×10×2铜管制成水冷线圈，并安装不锈钢水冷保护套，工频有芯熔炼炉的金属熔液即为感应器的次级线圈，整个电炉实际就是一个变压器，配套一台6档的自耦调压变压器，由电柜控制换档，电压可由低到高，分6级升到380V，每档电压不同，输出功率也不同，炉温也随档位不同而高低不同，以适应熔炼有色或黑色等熔点不同的金属，并可作新炉衬耐火冶金砂烘炉之用。

The furnace body is made ф2200×1500 theouter covering main body by the 12mm steel plate, lower part the furnace body 45° the installment has the sensor, the sensor orientation silicon steel plate is made the weight 2 ton induction iron cores by Wuhan Steel Corporation Silicon steel plate Factory production top gear's W-151 the cold rolling0.35m/m, primary is made the water cooling coil by 10×10×2 the copper pipe, and installs the stainless steel water cooling restricting, the power frequency has the core smelting furnace's metal melt fluid namely for the sensor sencondary coil, the entire electric stove is a transformer actually, thenecessary 6 grades from the pair regulating transformer, shift gears by the electricity cabinet control, the voltage may from low to high, divide 6 promotions to arrive at 380V, each grade of voltages are different, the output is also different, the furnace temperature along with the files position isalso different, but the height is different, adapts smelts colored or the black and so on melting point different metals, and may make the new furnace lining to smelt diamantine drying furnace fireproof.

炉体由12mm钢板制成Ф2200×1500外壳主体，炉体下部45°安装有感应器，感应器由武钢硅钢片厂生产的最高档的W-151冷轧0.35m/m取向硅钢片制成重2吨感应铁心，初级由10×10×2铜管制成水冷线圈，并安装不锈钢水冷保护套，工频有芯熔炼炉的金属熔液即为感应器的次级线圈，整个电炉实际就是一个变压器，配套一台6档的自耦调压变压器，由电柜控制换档，电压可由低到高，分6级升到380V，每档电压不同，输出功率也不同，炉温也随档位不同而高低不同，以适应熔炼有色或黑色等熔点不同的金属，并可作新炉衬耐火冶金砂烘炉之用。

A steel plate having a tensile strength of at least about 930 MPa (135Ksi), a toughness as measured by Charpy V-notch impact test at least about 120 joules (88 ft-lb), and a microstructure comprising at least about 90 volume percent of a mixture of fine-grained lower bainite and fine-grained lath martensite, wherein at least about 2/3 of said mixture consists of fine-grained lower bainite transformed from unrecrystallized austenite having an average grain size of less than about 10 microns and comprising iron and specified weight percentages of the additives: carbon, silicon, manganese, copper, nickel, niobium, titanium, aluminum, calcium,rare earth metals, and magnesium, is prepared by heating a steel slab to a suitable temperature; reducing the slab to form plate in one or more hot rolling passes (10) in a first temperature range in which austenite recrystallizes; further reducing said plate in one or more hot rolling passes (10) in a second temperature range in which austenite does not recrystallize, quenching (12) said plate to a suitable quench stop temperature (16); and stopping said quenching and allowing said plate to air cool (18) to ambient temperature.

一种钢板，其抗拉强度至少约930MPa135ksi），在－40℃（－40°F）下，采用夏氏V型缺口冲击试验测定的韧性至少约120焦耳（88英尺－磅），并且其显微组织包含至少约90％体积的细晶粒的下贝氏体和细晶粒的板条马氏体的混合物，其中该混合物的至少约2／3由从平均粒径小于约10微米的未再结晶奥氏体转变而来的细晶粒的下贝氏体组成，而且，其中所述的钢板包含铁和特定重量百分比的添加元素：碳、硅、锰、铜、镍、铌、钛、铝、钙、稀土金属和镁，所述钢的制备过程为：将一钢板坯加热至一个适当的温度；在奥氏体可发生再结晶的第一个温度范围内，采用一个或多个热轧道次（10），将所述板坯轧制成板材；在奥氏体不发生再结晶的第二个温度范围，采用一个或多个热轧道次（10）进一步轧制所述板材；将所述板材淬火处理（12）至一个适当的淬火终止温度（16）；停止所述淬火处理并将所述板材空冷（18）至室温。