plank-sheer

与plank-sheer相关的网络例句 [注：此内容来源于网络，仅供参考]

6 cases of urethostenosis, 2 cases of urotithiasis and 1 case of urethral valves were cured one time. They were followed up from 10 months to 6 years and no dysuria occurred. 2 cases of external plank shedding after ureteropelvioplasty were treated with a placement of internal plank through the renal fistulization. The placement and evulsion of internal plank were carried out one time in 8 cases of ureteric calculi (the length of one calculi was as long as 4cm) and 12 cases of ureteropalsty. In 5 cases of upper remotion of internal plank, 4 cases were pulled out successfully and one failed to draw out. The effect is satisfactory to treat urological diseases by means of ureteroscopy in children.

结果 6例尿道狭窄、2例尿道结石、1例尿道瓣膜均一次性治愈，随访10个月~6年，无排尿异常。2例肾盂输尿管成形术后外支架管脱落经肾造瘘口放置内支架；8例输尿管结石（1例石街长约4cm）、12例输尿管成形术后内支架置入和／或拔出均一次完成。5例内支架上移中4例顺利拔出，1例失败、结论输尿管镜对小儿尿路系统大部分疾病的处理有满意效果。

Diagram paper 9:The 1 F floor plank goes together with Jin diagram, the 5 F floor plank to go together with Jin diagram, the 1 F beam flat surface to go together with Jin diagram, the 5 F beam flat surface to go together with Jin diagram, 1 F pillar to go together with Jin plane chart, foundation flat surface to arrange diagram, foundation flat surface to set out big kind diagram, 3 stalk frames to go together with Jin diagram, stairs flat surface to arrange diagram and stairs plank to go together with Jin to arrange diagram.

图纸9张：一层楼板配筋图、五层楼板配筋图、一层梁平面配筋图、五层梁平面配筋图、一层柱配筋平面图、基础平面布置图、基础平面布置大样图、3轴框架配筋图、楼梯间平面布置图及楼梯板配筋布置图。

Common rolling plank is shown intense (orientaton of 0002) tool reference plane, after rolling of horn waiting for diameter, plank grain orientaton by original (change of orientaton of 0002) tool reference plane is; of orientaton of blame tool reference plane the existence after strain crack of common rolling plank is many twin brilliant, amount of brilliant of twin of drawing of direction of rolling of edge of plank of rolling of horn w

普通轧制板材呈强烈的(0002)基面取向，等径角轧制后，板材晶粒取向由原来的(0002)基面取向转变为非基面取向；普通轧制板材拉伸断裂后存在大量孪晶，等径角轧制板材沿轧制方向拉伸孪晶数量明显减少，等径角轧制有可能启动了新的滑移系，而拉伸孪生只是作为一种协调变形机制。

与plank-sheer相关的网络解释 [注：此内容来源于网络，仅供参考]

plank-sheer：船缘木

plank on edge 细长的 | plank sheer 船缘木 | plank sheer 船缘木木船)舷缘板

plank-sheer：船缘木木船)舷缘板

plank sheer 船缘木 | plank sheer 船缘木木船)舷缘板 | plank split 板裂缝