parameter curve

parameter curve的基本解释

-

[计] 参数曲线

与parameter curve相关的网络例句 [注：此内容来源于网络，仅供参考]

In this paper, a region approximation idea that means using a "fat curve" with a width to approximate the offset curve is proposed, and a complete set of algorithms to approximate offset curve using disk Bézier curve are given and implemented. In the algorithms, the optimal and uniform approximate curve of the offset curve as the central curve of the Disk Bézier curve is found by using Remez method, and then the upper optimal and uniform approximation principle is proposed to compute the error radius function of the Disk Bézier curve. Thus, the whole Disk Bézier curve can be obtained. In the end of this paper, the approximate effect of the Disk Bézier curve is not only analyzed and assessed, but also some specific examples are provided.

提出用一条带宽度的"胖曲线"来逼近上述等距曲线的区域逼近思想，并建立与实现了圆域Bézier曲线等距逼近的整套算法，包括应用Remez方法求出等距曲线的最佳一致逼近曲线作为圆域Bézier曲线的中心曲线，提出上控最佳一致逼近的原理求出圆域Bézier曲线的误差半径函数，以及确定整条圆域Bézier曲线，最后还对该圆域Bézier逼近的效果做了分析和考核，并给出了一些具体实例。

This paper establishes cubic spline function, analyzes subsection curve function and curve slope and curvature, at last decides to place the curve especial points which can be obtain easement curve length and other line parameters, such as the ZH point (end of line and beginning of transition curve), the HY point (end of transition curve and beginning of circular curve), the QZ point, the YH point (end of circular curve and beginning of transition curve), the HZ point (end of transition curve and beginning of line).

针对公路平面线形的8种组合类型，其线形元素特征则由最基本的直线、圆曲线、缓和曲线组成的特点，解析三次样条函数模型，得分段曲线函数、曲线斜率、曲率，从而确定曲线特征点（直缓ZH点、缓圆HY点、曲中QZ点、圆缓YH点、缓直HZ点）位置，进而得到曲线缓和曲线长度及其他线形参数。

First make the subjects give either right or wrong responses to the same question with different b value. When estimating the abilities of the subjects with the use of one-parameter or two-parameter Logistic model, it is found that there exists two kinds of unfits.(2) Estimate the abilities of the subjects after introducing c parameter on the basis of the two-parameter model. The first unfit can be rectified. However, the second unfit still exists and the third unfit appears.(3) Then estimate again after introducing y parameter. It is discovered that the second unfit is rectified, but the first unfit still exists and the fourth unfit appears.(4) Form Logistic four-parameter model by introducing c parameter and y parameter at the same time and estimate one more time. This model makes all kinds of unfits, including the first, second, third and fourth unfits, rectified.

1设计这批被试分别做对或做错一道b值不同的试题，用Logistic单、双参数模型对被试进行能力估计时，发现被试能力估计存在着两类失拟现象；(2)在双参数模型基础上增加c参数，对被试进行能力估计，发现c参数能有效纠正第一失拟现象，然而仍然存在第二失拟现象，同时还存在第三失拟现象；(3)在双参数模型基础上增加γ参数，再对被试进行能力估计，发现γ参数能有效纠正第二失拟现象，而仍然存在第一失拟现象，同时还存在第四失拟现象；(4)同时增加c、γ参数形成Logistic四参数模型，再对被试进行能力估计，这时该模型对各类失拟现象，包括第一、第二、第三、第四失拟现象都具有良好拟合能力。

与parameter curve相关的网络解释 [注：此内容来源于网络，仅供参考]

parameter curve：参数曲线

parameter 参数 | parameter curve 参数曲线 | parameter group 参数群

isothermal parameter curve：等温参数曲线

isothermal parameter 等温参数 | isothermal parameter curve 等温参数曲线 | isothermal surface 等温曲面

CONSTANT PARAMETER CURVE：等参曲线

Constant Offsets 常量偏移 | CONSTANT PARAMETER CURVE 等参曲线 | CONSTANT X-OFFSET 常X向偏移

parameter curve editing：参数曲线编辑

parallel projection 平行投影 | parameter curve editing 参数曲线编辑 | parameterized texture mapping 参数贴图

Parameter CUrve Out-of-Range Types：越界循环参数曲线

12.8 Make Controller or Object Unique控制器独立 | 12.9 Parameter CUrve Out-of-Range Types越界循环参数曲线 | 12.10 Add Note Track加入轨迹记录