packing nut
- packing nut的基本解释
-
-
填密螺母, 衬垫螺母, 密封螺母, 紧塞螺母
- 更多网络例句与packing nut相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Clean and check 1 slowly loosen the gland nut stuffing, packing the release of residual pressure of all components; 2 Remove all old packing, thoroughly clean axle / rod stuffing; 3 Check the shaft / bar have corrosion, dents, scratches or excessive wear; 4 Check whether there are other WATER POWER CONTROL VALVE parts burr, cracks, wear, they will reduce the packing life; 5 Check whether there is too much stuffing the gap, and the shaft / rod eccentric degree; 6 the replacement of defective parts larger; 7 Check the old packing, as BALANCING VALVES the basis of failure analysis to find the reasons for early failure of packing.
缓慢松开填料函的压盖螺母，释放盘根组件内所有的残余压力； 2）移去所有旧的盘根，彻底清洁轴/杆的填料函； 3）检查轴/杆是否有腐蚀、凹痕、划伤或过度磨损； 4）检查其他零件是否有毛刺、裂纹、磨损，它们会减少盘根的寿命； 5）检查填料函是否有过大的间隙，以及轴/杆的偏心程度； 6）更换有较大缺陷的零部件； 7）检查旧盘根，作为失效分析的依据，球阀以找到盘根早期失效的原因。
-
Adjusting the packing 1 Pump packing (1) continue to hand tighten the squeeze cap nut;(2) after opening the pump, adjust the gland nut, this time to allow a little more leakage;(3) slowly tighten the squeeze cap nut, gradually reduce the leak until the leak to an acceptable level;(4) If the disclosure of a sudden stop, should be back to tighten the gland nut, packing re-adjustment in order to prevent overheating;(5) adjust the leakage rate can reach a steady state.
泵用盘根（1）继续用手拧紧压盖螺母；（2）开泵后，调整压盖螺母，此时截止阀允许有稍多的泄漏；（3）缓慢地拧紧压盖螺母，逐渐减少泄漏，直到泄漏达到可接受的程度；（4）如果泄露突然停止，应回拧压盖螺母，重新调节以防止盘根过热；（5）调节泄漏率达到一个稳定状态即可。
-
The packing nut of this valve is secured by a lock nut with left-handed threads which prevents accidental loosening of the packing nut.
通过一个锁定螺母来固定密封螺母。锁定螺母带有左手螺纹，可以防止密封螺母的意外松动。
- 更多网络解释与packing nut相关的网络解释 [注：此内容来源于网络，仅供参考]
-
eyebolt nut：螺母
eyebolt 活节螺栓 | eyebolt nut 螺母 | packing bushing 填料压套
-
PACKING METHOD：包装法
充填工具 packing means | 包装法 packing method | 填密螺母 packing nut
-
piston rod packing：活塞杆填料
piston rod nut 活塞杆螺母 | piston rod packing 活塞杆填料 | piston rod stuffing box 活塞杆填料函