overlaps

overlaps的基本解释

-

[变形] overlap的第三人称单数

vt.

重叠, 重复, 与...同时发生

vi.

迭盖, 部分的同时发生

n.

重叠, 重复

与overlaps相关的网络例句 [注：此内容来源于网络，仅供参考]

Shrubs and undershrubs in desert-oasis ecotone can be divided into four groups based on the niche breadth. Based on the niche overlaps matrix, overlap between Reaumuria soongorica and Haloxylon ammodendron is large; overlaps among Kalidium foliatum、 Suaeda physophora、Kalidium caspicum、Tamarix ramosissima、T. elongata are large; the others'overlaps are small.

阜康荒漠绿洲过渡带灌木、半灌木按生态位宽度可分成4类；根据生态位重叠矩阵，红砂和梭梭之间、囊果碱蓬、里海盐爪爪、多枝柽柳和长穗柽柳之间重叠较大，其余种重叠值均较小。

Two-dimensional scatter plot of principal axes analysis,systematic cluster tree and the minimal spanning tree on the basis of niche overlaps were drawn,which revealed the ecological similarity of 42 moss species.The combinative application of principal axes analysis,systematic cluster analysis and minimal spanning tree method on the basis of niche overlaps could express the ecological similarities among species intuitively.

以此为指标，分别应用主坐标排序、图论聚类及系统聚类分析方法，作出了反映42种地面藓类的种间生态关系的二维投影图、最小生成树和动态聚类图。3种方法相结合，能够对生态位重叠值矩阵进行直观地表达，并使所表达的藓类种间关系具有确切的生态学含义。

Using the Shannon-Wiener's niche breadth index and the Pianka's niche overlaps index, we found that the Nereis japonica, nemerteans and eelworms had broad niche breadths (above 2.80); the niche overlaps among them was high (above 0.90) in the quantitative analysis on the 21 species present in the quantitative sample analysis.

对定量取样中获得的21个物种以Shannon-Wiener指数为基础进行了生态位宽度测定，以Pianka重叠指数为基础进行了生态位重叠值分析，结果表明日本沙蚕、纽虫和线虫的生态位较宽，均为2.80以上，它们之间的生态重叠值也较高，均为0.90以上。

与overlaps相关的网络解释 [注：此内容来源于网络，仅供参考]

overlaps：重叠部分

车门的重叠部分(overlaps)是为防止飞溅进入乘客车厢而专门设计的. 汽车的油箱和电池也得到了额外保护,同时轮胎可以在没气的情况下使用. 此外还配备了高强度的撑杆和强化的撑杆支撑点.

overlaps：重叠

例如表8-5显示了使用维度扩展九交模型描述的两个多边形a和b的重叠(Overlaps)关系. 例如模式"T*T***T**"表示的是空间关系重叠(Overlaps). MapGuide支持11种空间关系,它们的扩展九交模型定义如下所示,其中P代表0维的几何物体点和多点(MultiPoint),

overlaps：重耍

Overlapping route 重复路线 | Overlaps 重耍 | Overlay 加铺路面层

overlaps：覆盖

commences 开始 | overlaps 覆盖 | phase transition 相转变

Eliminate Overlaps：是否要消除元件重叠的情况

◆ Place Parts放置元件 | .Eliminate Overlaps是否要消除元件重叠的情况 | .Align Parts布局微调时,相邻的元件是否要对齐