minimizing method

minimizing method的基本解释

-

[计] 求极小值法, 极小化方法

与minimizing method相关的网络例句 [注：此内容来源于网络，仅供参考]

The details as follow: 1.Based on rules about form error in GB, mathematical models of form error are established including straightness error on the base of minimizing zone method、least-squares method and two dots linked method ; flatness error based on minimizing zone method、lease-squares method、diagonal line and three dots method; circularity and cylindricity error based on minimizing zone method、lease-squares method、minimum circumscribed circle and maximum inscribed circle.

具体内容如下：根据国标中形状误差的相关规定建立了各种要素评定方法的数学模型包括：直线度的最小区域法、最小二乘法、两端点连线法；平面度的最小二乘法、最小区域法、对角线法、三远点法；圆度和圆柱度的最小区域法、最小二乘法、最小外接圆法、最大内切圆法。

On the design of algorithms, a novel exact hierarchical delay analysis method for general circuits is proposed; based on the sensitization theorem for sequential circuits, an exact minimizing clocking method is proposed; based on Boolean process, a waveform simulation method considering interconnecting delay for logic circuit and a parallel waveform simulation method are proposed; a new method that transforms bit-level waveform polynomial to word-level polynomial model is proposed; a multiple valued synthesis algorithm based on multiple valued Boolean process and a wire-centered delay synthesis policy are proposed, in which timing planning, floorplanning, wire planning and optimal clock skew in early design are considered; a two-layers channel routing method for minimizing crosstalk under grid mode is proposed; based on the transition numbers theorems for waveform polynomial, a new method for generation of test with noise effects is proposed.

算法设计方面，提出了一种精确的通用电路层次化延时分析方法；基于时序电路的敏化定理提出时序电路最小时钟周期精确确定方法；提出基于Boolean过程论的考虑互连延迟的逻辑电路波形模拟方法，在分析了波形模拟适合并行化基础上，进一步提出一种并行波形模拟算法；提出一种将位级电路波形多项式描述转化成字级多项式描述的新方法；提出一种基于多值Boolean过程的多值电路综合算法以及一种将前期设计定时规划、前期设计的布局规划和线网结构化方法及低偏移的时钟分配等技术相结合的面向互连延时的综合策略；提出一种串绕最小化的网格模式下的双层通道布线方法；从波形多项式描述跳变数的定理出发提出了一种考虑噪声效应的测试生成新方法。

Main points of the thesis are as follows:(1) The main function models and information relations between these models in the CAPP system in the integrated CAD/CAM project are explained, a new process plan design method is mentioned based on analyses of process plan design. This method is based on the process plan prototype, and develops the prototype little by little until the perfect process plan is completed, the prospect of this method is discussed;(2) The feature abstracting rules and methods are studied, a feature coding system is developed based on GT, all the defined feature models are described by the mathematical methods;(3) The integrated method of CAD/CAPP based on features is mentioned, this method defines a feature exchanging model, and develops an interface software to exchange design data into technology data base, this technology data base includes the design and technology information of the parts;(4) The process plan reasoning method based on features is created, this method uses Mycin algorithm to solve the reasoning of the feature process plan. A process plan making system is developed. In this system part process plan is made by the semi-intelligent method, this method uses the feature reasoning, feature process chain searching and man-computer talking together;(5) The main structure of the HOPE system is introduced, a shaft drawing and its process plan made by this system are shown, the data process problem in process drawing making is also discussed;(6) A new method of describing process rule is introduced, this method uses IfThen rules and neural nets weight values together to describe process rules, the BP algorithm is adopted in this method;(7) The optimal machining sequence problem of the process steps on the same fixturing is discussed, optimal algorithms SA is applied to solve this problem, the result shows that this method is more efficient than the traditional method;(8) All jobs in the thesis are summarized. In order to carry out the research in the future, some rational proposals are given.

全文论述的内容主要有下列几个方面：(1)较为系统地阐述了CAD／CAM一体化工程项目中CAPP系统的主要功能模块及其信息流程，在分析工艺设计过程的基础上，提出了基于特征原型的渐进式工艺设计方法，并探讨了该方法的应用前景；(2)研究了零件特征提取的原则和方法，在成组技术的基础上，开发了一套基于特征的分类编码系统，并在提取零件特征的基础上，定义了零件特征的数据模型，开发了基于轴类零件特征的参数化设计系统；(3)研究了基于特征的CAD／CAPP集成的方法，通过定义零件特征数据模型的存储结构，开发了将设计数据转换到工艺数据库中的接口程序，为后续的CAPP系统提供必要的零件形状和工艺信息；(4)研究了基于特征的工艺推理方法，将Mycin算法应用到工艺决策中，开发了基于特征的工艺推理及工艺方案生成系统，在系统中综合运用特征推理、特征加工工艺链查询及人机对话相结合的半智能化方法确定零件加工工艺；(5)介绍了整个HOPE系统的总体结构，通过运行HOPE系统绘出了一轴类零件的零件图，并生成了该零件的加工工艺方案，初步探讨了基于特征的工序图生成技术中数据处理问题；(6)研究了工艺设计过程中知识如何有效表示的问题，提出了将显式的IF-THEN规则表示与隐式神经网络权值表示相结合的工艺知识表示方法，并利用BP算法进行了工艺知识表示的初步研究；(7)研究了工艺设计过程中同一安装下工步优化排序问题，利用神经网络中基于模拟退火的理论来解决该工步优化排序问题，实践证明该方法较传统的算法具有更高的效率；(8)总结了本文所进行的研究工作，为今后进一步开展工作提出了较为合理的建议。

与minimizing method相关的网络解释 [注：此内容来源于网络，仅供参考]

minimizing method：极小化法

minimization 极小化 | minimizing method 极小化法 | minimizing sequence 极小化序列

minimizing energy method：最小能量法

minimizing diameter therapy 减径矫治法 | minimizing energy method 最小能量法 | minimizing sequence 极小化序列