loop control

loop control的基本解释

-

环路控制

与loop control相关的网络例句 [注：此内容来源于网络，仅供参考]

The hot helium temperature follows HTR-10's nuclear power changes slowly, and there is a large coupling between them, so the RPHHT system adopts cascade control, the minor loop is fast, and the major loop is hot helium temperature control loop whose dynamic response is slow; there is also a large coupling between main helium loop and steam-water loop, and both the main steam temperature measure signal and the heating process of the once-through steam generator are delayed, therefore, the MHFMST applies cascade control, the minor is main helium flow control loop whose dynamic response is fast, and the major is the main steam temperature control loop whose dynamic response is slow.

本文运用机理建模法，建立了HTR-10系统动态控制模型，然后进行了动态性能仿真，将堆芯用集中参数表示，冷却剂按一维流动处理；直流蒸汽发生器按二回路工质不同的相分为预热段、蒸发段和过热段，建立了三环节控制模型，得到HTR-10系统控制模型；仿真结果与数值计算结果对比表明，本文所建立的控制模型，能近似地反映HTR-10的动态特性，适合设计控制系统。

PART 1 UNIT 1 B Electrical and Electronic Engineering Basics A Electrical Networks ———————————— 3 Three-phase Circuits A The Operational Amplifier ——————————— 5 UNIT 2 B Transistors A Logical Variables and Flip-flop —————————— 8 UNIT 3 B Binary Number System A Power Semiconductor Devices —————————— 11 UNIT 4 B Power Electronic Converters A Types of DC Motors —————————————15 UNIT 5 B Closed-loop Control of DC Drivers A AC Machines ———————————————19 UNIT 6 B Induction Motor Drive A Electric Power System ————————————22 UNIT 7 B PART 2 UNIT 1 B Power System Automation Control Theory A The World of Control ————————————27 —————29 The Transfer Function and the Laplace Transformation UNIT 2 B A Stability and the Time Response ————————— 30 Steady State————————————————— 31 A The Root Locus ————————————— 32 ————— 33 UNIT 3 B The Frequency Response Methods: Nyquist Diagrams UNIT 4 A The Frequency Response Methods: Bode Piots ————— 34 B Nonlinear Control System 37 UNIT 5 A Introduction to Modern Control Theory B State Equations 40 38 UNIT 6 A Controllability, Observability, and Stability B Optimum Control Systems UNIT 7 A Conventional and Intelligent Control B Artificial Neural Network Computer Control Technology A Computer Structure and Function 42 B Fundamentals of Computer and Networks 43 44 PART 3 UNIT 1 UNIT 2 A Interfaces to External Signals and Devices B The Applications of Computers 46 UNIT 3 A PLC Overview B PACs for Industrial Control, the Future of Control UNIT 4 A Fundamentals of Single-chip Microcomputer 49 B Understanding DSP and Its Uses 1 UNIT 5 A A First Look at Embedded Systems B Embedded Systems Design Process Control A A Process Control System B 50 PART 4 UNIT 1 Fundamentals of Process Control 52 53 UNIT 2 A Sensors and Transmitters B Final Control Elements and Controllers UNIT 3 A P Controllers and PI Controllers B PID Controllers and Other Controllers UNIT 4 A Indicating Instruments B Control Panels Control Based on Network and Information A Automation Networking Application Areas B Evolution of Control System Architecture PART 5 UNIT 1 UNIT 2 A Fundamental Issues in Networked Control Systems B Stability of NCSs with Network-induced Delay UNIT 3 A Fundamentals of the Database System B Virtual Manufacturing—A Growing Trend in Automation UNIT 4 A Concepts of Computer Integrated Manufacturing B Enterprise Resources Planning and Beyond Synthetic Applications of Automatic Technology A Recent Advances and Future Trends in Electrical Machine Drivers B System Evolution in Intelligent Buildings PART 6 UNIT 1 UNIT 2 A Industrial Robot B A General Introduction to Pattern Recognition UNIT 3 A Renewable Energy B Electric Vehicles UNIT 1 A

电路 2 电路或电网络由以某种方式连接的电阻器，电感器和电容器等元件组成。如果网络不包含能源，如电池或发电机，那么就被称作无源网络。换句话说，如果存在一个或多个能源，那么组合的结果为有源网络。在研究电网络的特性时，我们感兴趣的是确定电路中的电压和电流。因为网络由无源电路元件组成，所以必须首先定义这些元件的电特性。就电阻来说，电压-电流的关系由欧姆定律给出，欧姆定律指出：电阻两端的电压等于电阻上流过的电流乘以电阻值。在数学上表达为： u=iR (1-1A-1)式中 u=电压，伏特；i =电流，安培；R =电阻，欧姆。纯电感电压由法拉第定律定义，法拉第定律指出：电感两端的电压正比于流过电感的电流随时间的变化率。因此可得到：U=Ldi/dt 式中 di/dt =电流变化率，安培/秒； L =感应系数，享利。电容两端建立的电压正比于电容两极板上积累的电荷 q 。因为电荷的积累可表示为电荷增量 dq 的和或积分，因此得到的等式为 u=，式中电容量 C 是与电压和电荷相关的比例常数。由定义可知，电流等于电荷随时间的变化率，可表示为 i = dq/dt。因此电荷增量 dq 等于电流乘以相应的时间增量，或 dq = i dt，那么等式(1-1A-3)可写为式中 C =电容量，法拉。

PART 1 Electrical and Electronic Engineering Basics UNIT 1 A Electrical Networks B Three-phase Circuits UNIT 2 A The Operational Amplifier ——————————— 5 B Transistors UNIT 3 A Logical Variables and Flip-flop —————————— 8 ———————————— 3 B Binary Number System UNIT 4 A Power Semiconductor Devices —————————— 11 B Power Electronic Converters UNIT 5 A Types of DC Motors —————————————15 B Closed-loop Control of DC Drivers UNIT 6 A AC Machines ———————————————19 B Induction Motor Drive UNIT 7 A Electric Power System ————————————22 B Power System Automation PART 2 Control Theory UNIT 1 A The World of Control ————————————27 B The Transfer Function and the Laplace Transformation UNIT 2 A B —————29 Stability and the Time Response ————————— 30 ————————————— 32 Steady State————————————————— 31 UNIT 3 A The Root Locus B The Frequency Response Methods: Nyquist Diagrams ————— 33 UNIT 4 A The Frequency Response Methods: Bode Piots ————— 34 B Nonlinear Control System 37 UNIT 5 A Introduction to Modern Control Theory B UNIT 6 State Equations 40 38 A Controllability, Observability, and Stability B Optimum Control Systems UNIT 7 A Conventional and Intelligent Control B Artificial Neural Network PART 3 UNIT 1 Computer Control Technology A Computer Structure and Function B 42 43 44 Fundamentals of Computer and Networks UNIT 2 A Interfaces to External Signals and Devices B The Applications of Computers 46 UNIT 3 A PLC Overview B PACs for Industrial Control, the Future of Control 1 UNIT 4 A Fundamentals of Single-chip Microcomputer B Understanding DSP and Its Uses 49 UNIT 5 A A First Look at Embedded Systems B Embedded Systems Design PART 4 UNIT 1 Process Control A A Process Control System 50 B Fundamentals of Process Control 53 52 UNIT 2 A Sensors and Transmitters B Final Control Elements and Controllers UNIT 3 A P Controllers and PI Controllers B PID Controllers and Other Controllers UNIT 4 A Indicating Instruments B Control Panels PART 5 UNIT 1 Control Based on Network and Information A Automation Networking Application Areas B Evolution of Control System Architecture UNIT 2 A Fundamental Issues in Networked Control Systems B Stability of NCSs with Network-induced Delay UNIT 3 A Fundamentals of the Database System B Virtual Manufacturing—A Growing Trend in Automation UNIT 4 A Concepts of Computer Integrated Manufacturing B Enterprise Resources Planning and Beyond PART 6 UNIT 1 Synthetic Applications of Automatic Technology A Recent Advances and Future Trends in Electrical Machine Drivers B System Evolution in Intelligent Buildings UNIT 2 A Industrial Robot B A General Introduction to Pattern Recognition UNIT 3 A Renewable Energy B Electric Vehicles 2 UNIT 1 A

电路 电路或电网络由以某种方式连接的电阻器，电感器和电容器等元件组成。如果网络不包含能源，如电池或发电机，那么就被称作无源网络。换句话说，如果存在一个或多个能源，那么组合的结果为有源网络。在研究电网络的特性时，我们感兴趣的是确定电路中的电压和电流。因为网络由无源电路元件组成，所以必须首先定义这些元件的电特性。就电阻来说，电压-电流的关系由欧姆定律给出，欧姆定律指出：电阻两端的电压等于电阻上流过的电流乘以电阻值。在数学上表达为： u=iR (1-1A-1)式中 u=电压，伏特；i =电流，安培；R =电阻，欧姆。纯电感电压由法拉第定律定义，法拉第定律指出：电感两端的电压正比于流过电感的电流随时间的变化率。因此可得到：U=Ldi/dt 式中 di/dt =电流变化率，安培/秒； L =感应系数，享利。电容两端建立的电压正比于电容两极板上积累的电荷 q 。因为电荷的积累可表示为电荷增量 dq 的和或积分，因此得到的等式为 u=，式中电容量 C 是与电压和电荷相关的比例常数。由定义可知，电流等于电荷随时间的变化率，可表示为 i = dq/dt。因此电荷增量 dq 等于电流乘以相应的时间增量，或 dq = i dt，那么等式(1-1A-3)可写为式中 C =电容量，法拉。

与loop control相关的网络解释 [注：此内容来源于网络，仅供参考]

Loop Control Structure：回路控制结构

"回路控制叙述","loop control statement" | "回路控制结构","loop control structure" | "回路控制变数","loop control variable"

closed-loop control system：闭环控制系统

closed loop control 闭环控制 | closed loop control system 闭环控制系统 | closed loop system 闭环系统

closed-loop control system：闭合环路式控制系统

1429. closed loop control 闭合环路控制 | 1430. closed loop control system 闭合环路式控制系统 | 1431. closed loop gain 闭环增益