licker-in

licker-in的基本解释

-

(梳棉机)刺辊

与licker-in相关的网络例句 [注：此内容来源于网络，仅供参考]

The plates are obtained by two steps: compound felt and hot pressing shaping. The opening, mixture, carding, net-paving and needling process that affect shaping process of the blending fiber needle felt are investigated. Then it is concluded that the fiber nets from the BC-272B carding machines are uniform when the rolling speeds of licker-in, cylinder, doffer roller of the roller carding machine are 900r/min, 850r/min and 15.6r/min separately. The fiber needle felt is in a good condition when the paving nets have 8 layers, the type of the felting needle is 30, the density of needling is 1800end/m2, and the depth of needling is 3mm.

纤维复合板材分混合制毡和热压成型两步完成，分别探讨了开松、混合、梳理、铺网、针刺各工序对纤维针刺毡成型的影响，得出BC-272B罗拉梳理机的刺辊转速900r／min、锡林转速850r／min、道夫转速15.6r／min时，从梳理机下来的纤网较为均匀；铺网层数为8层、刺针型号为30、植针密度1800枚／m~2、针刺深度为3mm时，纤维针刺毡的效果较好，纤维复合针刺毡单位面积重量为200g／m~2。

Influences of Gauge between Licker-in and Carding Plate on Carding Sliver Quality;2. In order to fulfill the requirement of hi-production and hi-quality carding on carding degree,systematic analysis is done to the effect of carding plate as well as front and rear stationary flats.

为了满足梳棉机高产高质对梳理度的要求，系统分析了分梳板、前后固定盖板的作用效果，并通过试验说明适当扩大梳理面积和加装分梳板、固定盖板等措施可以增加分梳，以弥补梳理速度加速后梳理的不足。

Improper setting of feed plate to licker-in.

给棉板与刺辊的隔距不当。

Moreover, the company has the most advanced large machining center and production line of centrifugal castings, which can be used to produce various licker-in roller and roller castings covering the diameter within 1800mm and length within 3000mm.

另外公司还拥有国内最先进的大型机械加工中心、离心铸造设备流水线，可以生产加工直径1800mm ，长度3000mm 以内的各类刺辊和辊筒铸件。

The orthogonal experiment also indicates that the speed of cylinder., the speed of licker-in, the output speed of the carding sliver and the neps and short fibre. To further optimize the above four factors , a regress equation can be moleculed by the neps and the first three factors, Which can provide a theory for analyzhg neps controlling.

正交试验结果表明：锡林速度、刺辊速度、道夫速度、出条速度对棉结与短绒的影响不完全一致，在对这四个参数进行优化组合基础上，进一步建立棉结与锡林速度、刺辊速度、出条速度三个因素间的回归方程，为生条棉结控制提供了定性分析的理论依据。

与licker-in相关的网络解释 [注：此内容来源于网络，仅供参考]

licker-in undercasing：刺輥漏底

刺辊漏底 licker-in screen | 刺辊漏底 licker-in undercasing | 刺辊锯齿条 licker-in wire

licker-in roller：刺毛辊

licker-in grinding and covering machine 刺辊包磨机 | licker-in roller 刺毛辊 | licorice extract 甘草浸膏

licker-in grinder：磨刺辊机

刺辊 licker in | 磨刺辊机 licker-in grinder | 刺辊漏底 licker-in screen

licker-in screen：刺輥漏底

磨刺辊机 licker-in grinder | 刺辊漏底 licker-in screen | 刺辊漏底 licker-in undercasing

licker-in wire：刺輥鋸齒條

刺辊漏底 licker-in undercasing | 刺辊锯齿条 licker-in wire | 缠花,黏皮辊 licking