lead tolerance

lead tolerance的基本解释

-

[建] 容许含铅量, 四乙铅容许含量

与lead tolerance相关的网络例句 [注：此内容来源于网络，仅供参考]

Several studies have identified genes that play important roles in stress tolerance and virulence. For example, genes involved in osmotic stress tolerance, acid and alkaline tolerance, oxidative stress tolerance, extreme temperature tolerance, and bile salt tolerance have all been implicated in the virulence of L.

在压力存在的情况下能启动一些基因的表达，以增强细菌对环境的耐受性，这些基因包括与耐受渗透压、酸碱性环境、氧化、极端温度和宿主体内胆碱等环境压力相关的基因。

Influence of tolerance factor on the complex engine performance was analyzed, then a new tolerance analysis and optimization method for complex product was proposed. The method synthesized effects such as tolerance size, tolerance location and component error accumulation on the product performance. Tolerance was then optimized based on the result of tolerance analysis and processing cost of different parts.

分析了公差对复杂发动机性能的影响，提出了针对复杂产品的公差分析和优化方法，综合考虑了各零件公差值大小、公差分布位置和零件误差积累对产品性能的影响，并根据公差分析结果和零件的加工成本等综合因素对零件公差进行优化。

Roundness tolerance of pitch diameter Roundness tolerance for a minimum of 345o circumferential arc of the pitch diameter shall not exceed .002 inch (0.051 mm) total, or one half the pitch diameter tolerance if the pitch diameter tolerance is less than .004 inch (0.102 mm); roundness tolerance of the remaining 15o maximum circumferential arc shall not exceed .004 inch (0.102) total, provided such tolerance does not result in excrescence on the thread flank.

圆度公差沥青直径圆容忍最低限度的345o圆周弧音高直径不得超过0.002英寸（ 0.051毫米）总，或一的一半，足球场直径公差，如果沥青直径公差小于0.004英寸（ 0.102毫米）；圆的耐受性，其余15o最大周弧不得超过0.004英寸（ 0.102 ），共计提供这样的宽容不会导致在excrescence对线程的侧翼。

与lead tolerance相关的网络解释 [注：此内容来源于网络，仅供参考]

lead tolerance：导程公差

"前置时间","lead time" | "导程公差","lead tolerance" | "引导线(铁路)","lead track"

lead tolerance determination apparatus：四乙铅容许量测定器

lead titanate 钛酸铅 | lead tolerance determination apparatus 四乙铅容许量测定器 | lead tube 铅管

lead screw tolerance：丝杆公差

螺母公差 nut tolerance | 丝杆公差 lead screw tolerance | 外螺纹公差带 tolerance zone of male threads

Worm Lead form tolerance：蜗杆螺纹导程公差表

Worm Total Accumulated Pitch Variation 蜗杆总的积累齿距变化量 | Worm Lead Variation Tolerance 蜗杆螺纹导程变化公差 | Worm Lead form tolerance 蜗杆螺纹导程公差表

Worm Lead Variation Tolerance：蜗杆螺纹导程变化公差

Worm Total Accumulated Pitch Variation 蜗杆总的积累齿距变化量 | Worm Lead Variation Tolerance 蜗杆螺纹导程变化公差 | Worm Lead form tolerance 蜗杆螺纹导程公差表