inertia group

inertia group的基本解释

-

惯性群

与inertia group相关的网络例句 [注：此内容来源于网络，仅供参考]

In Chapter 1, assuming that the coefficient field κ is perfect and the order of the inertia group is coprime to the characteristic of κ, we prove the existence and the uniqueness of the hyperfocal subalgebra of a source algebra.

在第一章中，假设系数域是完全的；在惯性群的阶与系数域的特征互素的情况下，我们证明了源代数的超聚焦子代数的存在性与唯一性。

Have introduced its systematic structure and operation principle in the system of loading of the inertia, and the vibration question that should be paid attention to while designing a group of rotator inertial mass, describe a critical rotational speed of group of rotator inertial mass in detail, influence the factor of a critical rotational speed of group of rotator inertial mass, and rotate a critical rotational speed computing technology and rotation of group and a balance question of group of inertial mass of inertial mass , and confirmed a design of group of rotator inertia quality finally.

在惯量加载系统中介绍了其系统结构和工作原理，以及在设计旋转惯性质量盘组时应注意的振动问题，详细地论述了旋转惯性质量盘组的临界转速，影响旋转惯性质量盘组的临界转速的因素，以及旋转惯性质量盘组的临界转速的计算方法和旋转惯性质量盘组的平衡问题，并最后确定了旋转惯量质量盘组的设计。

Firstly, the transient stability of the modes by which some kinds of huge power suppliers are connected with AC power grid is analyzed and compared in detail; then a detailed transient stability simulation of a certain large-scale demonstration system is performed; finally some helpful conclusions are obtained: in the general situation, the bundling power transmission mode is favorable to increase the stability of sending system; if it is helpful to evidently increase the inertia of the equivalent leading group, the mode that connects the huge power supplier with sending system will be helpful to enhance the stability of sending system, however it is necessary to perform simulation and analysis while these principles are applied to FACT systems.

首先从机制上对几种大电源接入交流系统方式的暂态稳定性进行了详细的分析和比较；然后对大型算例系统进行了详尽的暂态稳定仿真；最终得出了一些有用的结论：一般情况下，打捆送电方式有利于提高送出系统的稳定性；如果有助于显著增加领前群的惯量，则与送端系统相联的方式也有助于提高送电系统的稳定性，但仍要结合具体系统进行分析。

Mechanical inertia identification method was deduced from the current model and the mechanical model of the PM motor.The gain of the speed controller was obtained through the mechanical inertia,a group of controller gains obtained through several turns of identification.

首先通过电机电流和电压方程以及运动方程推导出转动惯量的计算方法，再根据系统的转动惯量计算出速度控制器参数，在进行多次辨识和计算后，可以得到一组速度控制器参数。

Firstly, we prove the existence and the uniqueness of the hyperfocal subalgebra when the coefficient field is split for a defect pointed group; then, considering the structural pattern of source algebras over arbitrary fields, by means of G-acted groups, we reduce the existence and the uniqueness of the hyperfocal subalgebra over an arbitrary field to the case that the coefficient field is split for a defect pointed group and the inertia group stablizes a hyperfocal subalgebra.

首先我们证明了如果系数域对亏点群是分裂的，则源代数的超聚焦子代数存在且共轭唯一；然后通过考虑任意域上源代数的结构模式，以G-作用群为手段，将超聚焦子代数的存在性和唯一性归结为系数域对亏点群是分裂的情况下惯性群稳定的超聚焦子代数的存在性和唯一性。

与inertia group相关的网络解释 [注：此内容来源于网络，仅供参考]

inertia group：惯性群

inertia 惯性 | inertia group 惯性群 | inertial force 惯性力