indentation [,inden'teiʃən]

indentation的基本解释

n.

呈锯齿状, 缩排, 缺口, 印凹痕

indentation的同义词

n. indenture

与indentation相关的网络例句 [注：此内容来源于网络，仅供参考]

The main results of the investigation are as following:(1) Some important criteria for the design of multi-layer structure are acquired: the ratio of the layer thickness to the contact diameter should be controlled to a value about 0.8; increasing the number of the gradient layers and elasticity modulus of the top layer would benefit to the yield strength and the stress status at the interface.（2）By means of molecular dynamics simulations for a indentation and sliding process, it is discovered that dislocations of 45 direction to the surface occur in the surfaces layer, which is correspond to the direction of the plastic flows observed in the macroscopic continuous medium. The irreversible deformation caused by the dislocation and the atom piles at the surface are responsible for the irreversibility of the force response. They are also the main factors for the friction generation. The temperature and the indentation velocity have significant effects on the deformation behaviors of the material of the surface layer. The yield strength would increase obviously if the indentation velocity is greater than 10 m/s.（3）A method to evaluate the fracture toughness of coating by estimating the crack-density functionβof a Wicker''s indentation was proposed. Meanwhile a new surface treatment technology was developed using non-equilibrium plasma.（4）A MD-FE hybrid method and corresponding software was developed to analysis the tribological behaviors for multiplayer system.

研究主要内容和结果有：（1）得到指导梯度膜设计的几个准则：控制膜层厚度与接触半径比在0.8左右为宜；适当增加梯度层层数和顶层弹性模量，有利于提高抗屈服能力和改善界面处的应力状态；（2）通过对嵌入和滑动摩擦过程的分子动力学模拟，发现表层产生一个与宏观连续介质的塑性流动方向观测一致的45 方向位错；位错造成的不可逆变形和表面的原子堆积，是力的响应不可逆性的原因，也是构成摩擦力的主要因素；温度和嵌入速度对材料变形特性有显著的影响，当嵌入速度大于10 m/s时，屈服强度明显增加；（3）提出压痕裂纹密度系数β半定量判定膜层断裂韧性的方法；并开发出表面强化新工艺；（4）开发出分析表面摩擦学特性的MD-FE复合模拟方法和相应模拟软件。

The cracking of indentation was a new type of fracture problem. By using the energy release rate of boundary translation the fracture of indentation has been formulized and critical load and critical cracking angle of the indentation have been found.

压痕边界的开裂问题是一个新型的断裂力学问题，通过边界移动的能量释放率的分析给出了压痕边界开裂能量释放率数学表征，并给出边界开裂的临界载荷和临界开裂角。

If the indentation with cutter cut out paper edge will be affected by the indentation of positioning accuracy.

如果压痕后用切纸机不兵纸边裁切掉，不兵会感化压痕的定位精量。

与indentation相关的网络解释 [注：此内容来源于网络，仅供参考]

indentation：压痕

(1)硬度(hardness) 按相关学科的定义,硬度是指表面硬度,一般用"压痕"(indentation)法测定,即用一坚硬的圆锥体,用一定的力在材料的表面"压痕",由压痕的大小及深浅评定材料的表面硬度.

indentation：缩进

用"域表"(TBL REGIONS)菜单中的"缩进(Indentation)"命令,可为递归重复区域的报告数据指定缩进. 在重复区域的属性中只有下面两种组合情况可以显示缩进:Duplicates(多重记录)+ 递归的(Recursive)No Dup/level(无多重/级)+ 递归的(Recursive)用户在装配图中标注序号及指引线时,

indentation：内缩

3.Pseudo code(虚拟码):主要是运用结构化程序设计的基本逻辑结构、内缩(indentation)的撰写方法及程序语言中的符号说明程序的步骤,不仅可提供程序设计的参考,更可避免直接撰写程序的缺点.

indentation：缩进排版

4 缩进排版(Indentation) 4个空格常被作为缩进排版的一个单位.缩进的确切解释并未详细指定(空格 vs. 制表符).一个制表符等于8个空格 4.1 行长度(Line Length) 尽量避免一行的长度超过80个字符,因为很多终端和工具不能很好处理之.

indentation test：压痕试验

[1-2]c、以压痕试验(indentation test)及刮痕试验(scratch test),评估镀膜与基材的附著性. 图二为CrAlC镀膜表面做能量分散光谱仪(EDX)分析之结果,其结果显示Cr、Al、C各元素分布相当均匀,无元素集中现象且镀膜厚度均匀,显示沉积之过程稳定.