hum reduction factor

hum reduction factor的基本解释

-

滤波因数, 交流声降低因数

与hum reduction factor相关的网络例句 [注：此内容来源于网络，仅供参考]

With the raw material and the particle size of reducing agent narrowed, the percent reduction of strontia increases.(6) With the barbecuing pressure increasing, the percent reduction of strontia increases, after the certain value, the percent reduction of strontia decreases instead.(7) With reduction temperature increasing, the percent reduction of strontia increases.(8) The percent reduction of strontia is increasing with prolonging reduction time. In this experimental condition, it will become steady after 2.5h.

通过实验研究确定以SrCl_2-SrF_2-SrCO_3的纯锶盐体系作为电解质，实验中还采用了我们最新研制的熔盐电解监控仪对电解过程进行测量和系统的研究，得出以下结论：(1)增加电流强度，反电动势亦随之增加，而升高温度反电动势则有所降低；(2)随着电流密度的升高和电解时间的延长，电流效率逐渐增加，达到峰值后稳步下降；(3)延长电解时间，合金中锶的含量逐渐增加，最高可达18.1％；(4)开始电解后，反电动势逐渐增加，但向熔体中加入SrCO_3后，反电动势明显降低，因此认为在正常电解时是SrCO_3在分解。

In the paper,the transmission of designed roller oscillating tooth reduction gear adopts osci llating tooth gear drive without exception,one-stage reduction gear and two-stage reduction gear have joined through spline coupling band;The joining way of shock wave thellomble and oscillating tooth adopts the biserial bearing of without inner ring of needle bearing,and directly adopts bearing outer ring as shock wave thellomble;Center wheel of two-stage reduction gear and center wheel of two-stage reduction gear passes through taper thread,and center wheel is fixed;As soon as the flange of input end and center wheel of one-stage reduction gear,the flange of export end and center wheel of two-stage reduction gear makes monobloc structure.

本文预设的井下减速器的传动均采用活齿传动，一级减速器的输出轴和二级减速器的输入轴通过花键联轴套联接；激波环与活齿的毗连方式采用能蒙受较大载荷的无内圈双列滚针不锈钢管，且直接采用不锈钢管外圈作为激波环；一级减速器的中心轮和二级减速器的中心轮是通过锥螺纹毗连的，且中心轮固定；一级减速器的中心轮与输入端的法兰盘，二级减速器的中心轮与输出端的法兰盘均做成整体的结构。

In the paper,the transmission of designed roller oscillating tooth reduction gear adopts oscillating tooth gear drive without exception,one-stage reduction gear and two-stage reduction gear have joined through spline coupling band;The joining way of shock wave thimble and oscillating tooth adopts the biserial bearing of without inner ring of needle bearing,and directly adopts bearing outer ring as shock wave thimble;Center wheel of two-stage reduction gear and center wheel of two-stage reduction gear passes through taper thread,and center wheel is fixed;As soon as the flange of input end and center wheel of one-stage reduction gear,the flange of export end and center wheel of two-stage reduction gear makes monobloc structure.

本文设计的井下减速器的传动均采用活齿传动，一级减速器的输出轴和二级减速器的输入轴通过花键联轴套联接；激波环与活齿的连接方式采用能承受较大载荷的无内圈双列滚针中国财经圈，中国财经圈，且直接采用进口中国财经圈外圈作为激波环；一级减速器的中心轮和二级减速器的中心轮是通过锥螺纹连接的，且中心轮固定；一级减速器的中心轮与输入端的法兰盘，二级减速器的中心轮与输出端的法兰盘均做成整体的结构。

与hum reduction factor相关的网络解释 [注：此内容来源于网络，仅供参考]

hum modulation：哼声调制

hum filter 哼声滤波器 | hum modulation 哼声调制 | hum noise 哼声

hum balancer：交六平衡器

hum 哼声 | hum balancer 交六平衡器 | hum level 哼声电平

hum balancer：交流平衡器

1106. hum 交流声,咛声,哼声 | 1107. hum balancer 交流平衡器 | 1108. hum level 哼声电平