high-pressure cylinder

high-pressure cylinder的基本解释

-

高压汽缸

与high-pressure cylinder相关的网络例句 [注：此内容来源于网络，仅供参考]

Cylinder, the cylinder sets of radial a surplus deformation of the cylinder sets a great impact on the cylinder liner reduced radial a surplus amount to reduce the deformation of the cylinder sets, the top surface of the body decreases roughness, but it will increase the body on the plane cylinder only mouth the roughness ; Preload reduced cylinder head bolt deformation of the cylinder liner little effect, the body can reduce the top surface roughness and cylinder body on the plane I ended roughness; Shen appropriate reduced cylinder head bolt hole deep can reduce the deformation of the cylinder sets, but will cause the body and the top surface roughness on the cylinder body only I roughness increases Plane .

工作工况下，对于第2缸来说，气缸套径向过盈量对气缸套变形影响很大，减小气缸套径向过盈量，有利于减小气缸套的变形，减小机体顶面不平度，但会增大机体上缸套止口平面的不平度；减小缸盖螺栓预紧力对气缸套变形影响很小，可减小机体顶面不平度和机体上缸套止口平面的不平度；适当减小缸盖螺栓沉孔深可以减小气缸套的变形，但会造成机体顶面不平度和机体上缸套止口平面不平度的增大。

The production of various specifications of models of the general pressure gauge, pressure gauge in high pressure, pressure controller, pressure gauge controller, seismic pressure gauge, pressure gauge earthquake-resistant, resistance FarEasTone pressure gauge, dual scale pressure gauge calibration and three, stainless steel pressure gauge pressure recorder, oxygen pressure gauge, a wind pressure gauge diaphragm pressure gauges, diaphragm pressure gauges, diaphragm pressure gauge, pressure gauge needle, explosion-proof electric contact pressure gauges, explosion-proof induction type contact pressure gauge, ultra-high pressure manometer.

生产各种规格型号的普通压力表，中高压压力表，压力控制器，压力表式控制器，抗震压力表，耐震压力表，电阻远传压力表，双刻度及三刻度压力表，不锈钢压力表，压力记录仪，氧压力表，出风压力表膜盒压力表，膜片压力表，隔膜压力表，双针压力表，防爆电接点压力表、防爆感应式接点压力表，超高压压力表。

Caused by disc brake on the brake Wheel Cylinder could not return to places 4 possible: First, 5 foot brake valve exhaust port blocking, high-pressure gas instinct platoon atmosphere, caused by gas-liquid master cylinder of the spring could not return to place, resulting in the system move oil, brake disc brake Wheel Cylinder Piston top dead and could not return to places; second is to the disc brake master cylinder gas-liquid pipeline blockage, resulting in brake Cylinder piston can not return to place; third master cylinder of the gas-liquid Spring itself can not return to position, brake fluid under high pressure gas can not return Axial pump to gas-liquid master cylinder reservoir chamber, resulting in brake Cylinder piston can not return to places; Fourth Wheel Cylinder piston disc brake system, due to moving fluid dirty or rusty card dead and can not return to the piston position.

造成盘式制动器上的制动分泵不能回位有4种可能：一是脚制动阀5的排气口堵塞，高压气体本能排人大气，造成气液总泵的弹簧不能回位，导致制动油将盘式制动器的制动分泵活塞顶死而不能回位；二是气液总泵至盘式制动器的油管堵塞，造成制动分泵活塞不能回位；三是气液总泵的弹簧本身不能回位，制动液在高压气体作用下，不能回到气液总泵的储油室，从而造成制动分泵活塞不能回位；四是盘式制动器制动分泵活塞由于制动液太脏或活塞生锈卡死而不能回位。

与high-pressure cylinder相关的网络解释 [注：此内容来源于网络，仅供参考]

high-pressure cylinder expansion：高压缸膨胀

769.大轴晃动值 shaft swinging value, shaft eccentricity | 770. 高压缸膨胀 high-pressure cylinder expansion | 771.中压缸膨胀 intermediate pressure cylinder expansion

Forged-steel single-acting high-pressure cylinder：锻钢制单作用高压气缸

Two-stage double-acting compressor cylinders with intercooler 带级间冷却器的两级双作用压气机气缸 | Forged-steel single-acting high-pressure cylinder锻钢制单作用高压气缸 | 1 inlet气体进口