heat radiation

heat radiation的基本解释

-

[化] 热辐射

与heat radiation相关的网络例句 [注：此内容来源于网络，仅供参考]

According to the studied results at present, the studied objects are mainly thin plate and beam about sound radiation mode, a method computed sound radiation mode of complex structure is presented in this dissertation, according to the results of the previous two chapter, a theoretical method to solve acoustical radiation mode and acoustical radiation efficiency of complex structure by boundary element method and acoustical radiation theory is posed, the acoustical radiation power is expressed as a Hermitian quadratic form, while the radiation modes is determined by general eigenvalue decomposing, and then the radiation efficiency is computed via the orthodoxy of radiation modes with regard to impedance matrix and average velocity matrix; lastly, the validity of the method is proved by pulsating sphere and radiating cube with analytical results. According to results of the form three chapter, the structure sound radiation sensitivity is studied in detail, the sound radiation power of structure can be expressed as positive Hermitian quadratic form, the sound radiation sensitivity can be expressed as two parts by partial differential with respect to design variable, which are sensitivity of boundary velocity and impedance matrix, combined with the theory of FEM and BEM, the structure sound radiation can be translated to the analysis of structure dynamic sensitivity and impedance matrix sensitivity. The theory posted in this dissertation is tested by the FEM software ANSYS and the software AAS programmed by author.

在前几章的基础上，通过结构声辐射的模态理论对结构的声辐射的机理进行了深入地探讨，针对目前声辐射模态的研究对象主要是简单的板和梁类结构，提出了一种计算复杂结构声辐射模态的方法，利用前两章研究所得的结论，将边界元方法与广义特征值的理论结合起来研究了复杂结构的声辐射模态与声辐射效率，先将结构的声辐射功率表示为一个正定的厄米特二(来源：ABb7C论文0909网www.abclunwen.com)次型，运用广义特征值分解求解了复杂结构的声辐射模态，然后利用声辐射模态关于阻抗矩阵与均方速度耦合矩阵的正交性，求解了复杂结构的声辐射效率，最后用具有解析解的脉动球与辐射立方体验证了该方法的有效性。

Based on a computing model of floor heating residences, indoor thermal environment and heat distribution under the effect of heat charge/discharge, operation control and solar radiation has been concluded. Concept and formula of equivalent heat supply has been put forward which indicate that actual heat supply will be equal to the sum of design heat supply and equivalent heat supply. Recommend coefficient has been given taken Dalian as an example. Computed according to the new method, design heat supply can be reduced to 37% in cloudy day and 43.3% in sunny day, energy saving effect is very obvious. In Tromb wall solar house, effect of concrete wall on indoor temperature swing and attenuation of temperature wave is very obvious. While the outdoor air-temperature swing exceeds 10℃, indoor air-temperature swing belows 3℃. In the experiment, maximal difference in temperature between inner surface and outer surface of the 300mm wall exceeded 10℃. Heat storage and collector efficiency varies adversely according to solar radiation. Factors such as thickness, material, absorptance of the wall and permeation of the glass cover all have big influence on heat storage and collector efficiency. There exsisted an optimal thickness of the wall, which can make the best of heat storage and collector efficiency. Most of the heat stored in conventional Trombe wall during the daytime has been lost to the outside at night without heat preservation. Heat preservation on the outside surface of the wall has effectively improved heat release performance of the wall at night, heat supply to the room has increased too.

通过建立的地板采暖系统动态热性能分析模型，得出了在蓄放热特性、运行方式和太阳辐射等因素耦合作用下的室内热环境及热量分配比例，提出了等效供热量的概念及计算公式，指出实际所需供热量应等于设计供热量加上等效供热量，并以大连为例，给出了等效供热量的修正系数，以新方法计算，阴天可减少设计供热量37％，晴天最大可以减少设计供热量43.3％，节能效果显著；集热蓄热墙式太阳房中，混凝土蓄热墙的室温均一化效果和对温度波的削减作用非常明显，当室外温度波动最大幅度超过10℃时，室温波幅不超过3℃，实验中300mm厚墙体内外表面温差超过10℃；墙体蓄热效率与集热效率随太阳辐射照度的变化呈相反的变化趋势；墙体厚度、材料、表面吸收率以及盖板透过率等因素对集热和蓄热效率均有较大的影响，存在一个最佳的墙体厚度值，使得墙体集热和蓄热综合性能最优；传统的蓄热墙夜间没有外保温，辐射散热损失很大，研究表明墙体外保温方式明显改善了蓄热墙夜间的散热性能，增加了向室内的供热量。

The method of CFD numerical simulation is employed to replace experimental investigation. Hence, STAR-CD of the commercial software is used to simulate the outer flow field and heat transfer performance of integrated heat sink with heat pipes cooled by airflow. It is found that simulated results agree with experimental results well, which indicates that simulation method is reasonable and reliable. Further, simulated computations for different fin thickness, fin pitches and air velocities are performed to analyze their effects on heat transfer performance of heat sink. Finally, a new optimized structure of integrated heat sink with heat pipes is provided to meet future demands for cooling CPU and its heat transfer is also evaluated. For multi-heat source and higher dissipation power of electronic devices, the integrated heat sink with heat pipes attatched fins stagged in different positions of channels is presented and its flow and temperature fields are also simulated to enhance heat transfer. As a conclusion, all mentioned above are useful for the design of heat sink with excellent efficiency of heat dissipation and further research.

应用商业软件Star-CD对CPU集成热管散热器的外部流场和传热特性进行了数值模拟，将数值模拟结果和试验结果对比，验证了所提出的数值计算方法是可靠和可行的；利用此数值模拟方法对CPU集成热管散热器在不同散热翅片间距、厚度和气流速度下散热器的流动与传热性能进行了数值计算，分析了这些参数的变化对散热器传热性能的影响；针对未来CPU冷却的要求，确定了与最优气体流速匹配的最佳翅片间距、厚度的CPU集成热管散热器的新结构；利用试验评测了根据数值模拟提供的新结构开发出的新CPU集成热管散热器的传热性能；最后在场协同强化传热的理论的基础上，对CPU集成热管散热器的散热翅片错位排列来强化散热器的散热，满足未来大功率、多热源的电子元件的散热，为今后进一步优化散热器提供了依据。

与heat radiation相关的网络解释 [注：此内容来源于网络，仅供参考]

heat radiation：热辐射

热量传递共有三种基本方式:热传导(Heat Conduction);热对流(Heat Convection);热辐射(Heat Radiation)当物质微观粒子(原子)内部的电子受激和振动时,将产生交替变化的电场和磁场,所发出电磁波向空间传播,即为热辐射.

heat radiation：熱放射

heat pump 熱ポンプ,ヒートポンプ | heat radiation 熱放射 | heat rate 熱消費率

heat radiation：輻射熱

"辐射热","heat, radiating" | "辐射热","heat, radiation" | "放射性热","heat, radioactive"

heat radiation：热辐射=>熱放射

heat radiating equipment 热辐射设备 | heat radiation 热辐射=>熱放射 | heat radiator 散热器

heat radiation pyrometer：热辐射高温计

热辐射 heat radiation | 热辐射高温计 heat radiation pyrometer | 加热率 heat rate