gig mill

gig mill的基本解释

-

拉绒厂

与gig mill相关的网络例句 [注：此内容来源于网络，仅供参考]

The classification of our main tools is comprehensive, including Long Neck Square /Ball Type End Mill, Ripple Roughing End Mill, High Spiral End Mill For Aluminum, Nose Type End Mill, Micro Diameter Square/ Ball Type End Mill , Taper Neck End Mill, Long Flute End Mill, Long Shank End Mill, Two/Three/Four/Six/Eight Flutes End Mill, etc.

公司主要产品有：深沟专用长颈平头/球头立铣刀，波纹粗铣刀，高螺旋铝用立铣刀，圆鼻铣刀，微小径平头/球头立铣刀，斜颈铣刀，长刃立铣刀，长柄立铣刀，二刃、三刃、四刃、六刃、八刃等多刃立铣刀等。

Here now figures of maximum, average and minimal sequential brust speedfor all the discs.They are thus 7200.10 the fastest with 60 to 61.8 M/S average and 74.9 to 76.3 M/S as peak:the 750 Gig diskhas better performance over the 500 Gig one dueto theuses of larger plates offering a greater density (187,5 Gig vs167 Gig).Western follows closely, and then come theMaxtor.

在这里，现在的数字最高，平均及最低限度的顺序brust速度为所有discs.they因而7200.10最快的60个达到6180米/秒，平均和74.9 ，以76.3米/秒，因为高峰： 750 gig的硬盘有更好的表现超过了500 gig的一个因使用较大的板提供了更大的密度（ 187，5 gig的比167 gig的）。

Here now figures of maximum, average and minimal sequential brust speedfor all the discs.They are thus 7200.10 the fastest with 60 to 61.8 M/S average and 74.9 to 76.3 M/S as peak:the 750 Gig diskhas better performance over the 500 Gig one dueto theuses of larger plates offering a greater density (187,5 Gig vs167 Gig).

现在这里的数字，1537平均最低时序brust速度为所有discs.they因而7200.10最快的有60至61.8米/秒，平均74.9至76.3米/秒的峰值为：750gig磁盘有更好的表现超过了500gig之一，由于用途大板，提供了更大的密度(187，5gigvs167gig)。

与gig mill相关的网络解释 [注：此内容来源于网络，仅供参考]

GIG：里约热内卢

百慕大国际 (BDA) 里约热内卢 (GIG)从百慕大国际 (BDA)飞往里约热内卢 (GIG)的转接航班百慕大国际 (BDA) 里约热内卢 (GIG)百慕大国际 (BDA) 里约热内卢 (GIG)

breakdown mill, cogging mill, primary mill：开坯机

? 方板坯初轧机 blooming slabbing mill | ? 开坯机breakdown mill, cogging mill, primary mill | ? 二辊式轧机 two high rolling mill

roller mill, bowl mill, disk roll mill：中速辊式磨煤机

154.钢球磨煤机 tube mill | 155.中速辊式磨煤机 roller mill bowl mill disk roll mill | 156.双进双出钢求磨煤机 double inlet and outlet tube mill