gearing ['giəriŋ]

gearing的基本解释

-

[变形] gear的现在分词

n.

传动装置

与gearing相关的网络例句 [注：此内容来源于网络，仅供参考]

The tongs all passes in the machine the gearing on the bed what tongs the gearing on realizes with superficial contact in the cowgirl on the bed in machine or matches.when the tongs installs in the machine bed work on the stage,the center of gravity of the tongs should be as far as possible low,center of gravity the more high an accepts should the dint is more big,the tongs bottom four directions should bulge,make its contact good,or the bottom establishes four a feets.when the tongs installs on the machine bed principal axis,the tongs install the to should have the enough match accuracy with principal axis cowgirl surface,and guarantee the gearing the stability dependable.

夹具体在机床上的安装都是通过夹具体上的安装基面与机床上的相应表面的接触或配合实现的。当物流设备需要的公司体在机床工作台上安装时，夹具的服装厂应尽量低，重心越高则支承面应力越大，夹具底面四边应凸出，使其接触良好，或底部设置四个支脚。当夹具体在机床主轴上安装时，夹具安装基面与主轴相应表面应有足够的配合精度，并保证安装稳定可靠。

In this dissertation, first, based on theory of cutting tooth about the gleason spiral bevel gear, the equation of meshing in the process of cutting tooth, the surface equation of generating gear as well as the general tooth surface equation of the double circular arc spiral bevel gear, using GB12759-1991 type of double circular arc gear as a basic gear profile, a three-dimension solid model of double circular arc spiral bevel gear which has the good adaptability was carried out by used of Unigraphics software;Second, by researching of the algorithm about contact and collision as well as various contact types based upon Contacting Finite Element Method, a foundation was laid for selecting the contact type in analyzing contact stress of double circular arc spiral bevel gearing;Finally, through the connection port of PARASOLID between UG software and ANSYS/LS-DYNA software, the three-dimension solid model of double circular arc spiral bevel gearing obtained above in UG was imported into ANSYS/LS-DYNA, a finite element analyzing about contact stress of double circular arc spiral bevel gearing was carried out by applying new loading method.

本文首先基于格利森弧齿锥齿轮加工原理及切齿啮合过程中的啮合方程、产形轮齿面方程以及双圆弧弧齿锥齿轮的齿面方程，选用GB12759-1991型双圆弧齿轮基本齿廓为基准齿形，利用Unigraphics软件的建模功能，绘制了有较好适应性的双圆弧弧齿锥齿轮传动三维实体模型。其次，描述了应用有限单元法进行实体接触与碰撞问题算法的公式，研究了有限元分析中的各种接触类型以及双圆弧弧齿锥齿轮接触应力分析中所选择接触类型的依据。最后，通过UG软件和ANSYS/LS-DYNA之间的PARASOLID接口工具包，将UG软件中得到的啮合齿轮模型导入ANSYS/LS-DYNA有限元分析软件，给出一种新的加载方法，进行了双圆弧弧齿锥齿轮传动的接触应力的有限元分析。

They are divided into two main classes: one class with handwheels but no gearing, and the other class with cranking actuators and worm gearing or worm and spur gearing combined.

这些地轴架分为两大类：一类配置手轮，没有齿轮执行机构；另一类配置转动曲轴执行机构和蜗轮或蜗轮和凸轮组合执行机构。

与gearing相关的网络解释 [注：此内容来源于网络，仅供参考]

gearing：财务杠杆

其次,从财务杠杆(Gearing)的角度来说, 股本资金的成本通常为20%左右,借贷资金的成本一般在10%上下. 由于两者之间成本存在差异,所以它们在资金总额中的比重变化会直接影响到全部资金的平均成本(Average

gearing：传动

我们提供的模块化轴代码有自动寻的(Homing)、啮合传动(Gearing)、凸轮传动(Camming)等全功能动作. 这些代码可以用作修改具体应用程序的基础,也可以用作程序要求的通常类型的建议结构样本.

gearing：资本充足率

gear ratio资本充足率 | gearing资本充足率 | general intangible一般无形物

gearing：财务杠杆率

gaap 公认会计准则 | gearing 财务杠杆率 | geographical spread of markets 市场的地理扩展

chain gearing：链传动装置

链 chain | 链传动装置 chain gearing | 链轮 sprocket ; sprocket-wheel ; sprocket gear ; chain wheel