flat back

flat back的基本解释

-

[医] 板样背

与flat back相关的网络例句 [注：此内容来源于网络，仅供参考]

The main reason why quarter-sawn board of Birch had smaller dry compressing shear strength than flat-sawn board of Birch in normal conditions was that Birch had different shear strength to the grain between quarter-sawn board and flat-sawn board. Meanwhile xylary rays in flat-sawn board were transversely cut and left a lot of pores in the flat-sawn board, so adhesive can enter these pores and turn into adhesive nail. While these pores provided a kind of tunnel for water, so cause this phenomenon that wet compressing shear strength of flat-sawn board of Birch was smaller than that of quarter-sawn board of Birch. The possible reason why quarter-sawn board of Oak had greater dry compressing shear strength than flat-sawn board of Oak in normal conditions was that ratio of springwood on quarter-sawn board and flat-sawn board was different.

造成柞木径切板的常态压缩剪切强度比弦切板的常态压缩剪切强度大的主要原因是，在径切板和弦切板上早材胶接的比例不同，径切板的胶合强度试件上早材胶接的比例相对少，而弦切板的胶合强度试件上早材胶接的比例比径切板的胶合强度试件上早材胶接的比例相对大，由于早晚材胶接过程中强度决定于早材，这部分胶接强度比较低，这就使得柞木径切板的常态压缩剪切强度比弦切板的大；同时在柞木弦径面胶接过程中由于实际胶接面积的不同也能造成弦径面上API胶粘剂与之形成的化学键的数量不同，这也是造成柞木径切板的常态压缩剪切强度比弦切板的大的原因之一。

Now has casting, machining, finishing, flat-panel and other refinements of the workshop, the main products are cast iron flat-panel, flat line, the assembly of flat, square box, V-Rail, V-plane, parallel flat foot, the bridge-ping feet square, feet, machine-specific point of foot, bending plate, ladder Sizing Block, contour Sizing Block, migraine pendulum tester, gear beating device, machine tool inspection wand Adjustable Sizing Block Machine, Machine Tool Sizing Block shockproof, special wrench , explosion-proof tools, such as on-arc model; granite platform, flat feet, feet, square box, V-blocks, granite, table, Block, measuring instrument, such as granite.

现在有铸造、机加工、精加工、精研平板等车间，主要产品有铸铁平板、划线平板、装配平板、方箱、V型铁、V型架、平行平尺、桥型平尺、直角尺、方尺、机床专用角度尺、弯板、阶梯垫铁、等高垫铁、偏摆检查仪、齿轮跳动仪、机床检验棒、机床可调垫铁、机床防震垫铁、特种扳手、防爆工具、对弧样板等；花岗石平台、平尺、方尺、方箱、V型块、花岗石表座、花岗石测量仪等。

Now has casting, machining, finishing, flat-panel and other refinements of the workshop, the main products are cast iron flat-panel, flat line, the assembly of flat, square box, V-Rail, V-plane, parallel flat foot, the bridge-ping feet square, feet, machine-specific point of foot, bending plate, ladder Sizing Block, contour Sizing Block, migraine pendulum tester, gear beating device, machine tool inspection wand Adjustable Sizing Block Machine, Machine Tool Sizing Block shockproof, special wrench , explosion-proof tools, etc.; granite platform, flat feet, feet, square box, V-blocks, granite, table, Block, measuring instrument, such as granite.

现在有铸造、机加工、精加工、精研平板等车间，主要产品有铸铁平板、划线平板、装配平板、方箱、V型铁、V型架、平行平尺、桥型平尺、直角尺、方尺、机床专用角度尺、弯板、阶梯垫铁、等高垫铁、偏摆检查仪、齿轮跳动仪、机床检验棒、机床可调垫铁、机床防震垫铁、特种扳手、防爆工具等；花岗石平台、平尺、方尺、方箱、V型块、花岗石表座、花岗石测量仪等。

与flat back相关的网络解释 [注：此内容来源于网络，仅供参考]

flat back：平底法,单面压花法

flashing chamber 闪击室 | flat back 平底法,单面压花法 | flat bed press 平版印刷

flat back：平背

flap jack-knife somersault dive 飛身鐮刀式翻騰跳水 | flat back 平背 | flat drive 平抽

flat back：背脊

43. matt lamination 哑膜 | 44. flat back 背脊 | 45. H&T bands hand and Tail 天头地却加堵头布

flat back：平脊

flat armature 边衔铁,扁平衔铁 | flat back 平脊 | flat back pattern 平接模

flat back method：上向梯段开采法

flat back cut and fill method 水平分层充填开采法 | flat back method 上向梯段开采法 | flat bed 平层