filling-in

filling-in的基本解释

-

放进, 填满, 填入

与filling-in相关的网络例句 [注：此内容来源于网络，仅供参考]

Result Richards Model and Monodic Quadratic Equation could properly describe grain dry matter growing process and the change process of grain filling rate with days after anthesis. There was big difference in average grain filling rate, maximum grain filling rate under different planting density. Average grain filling rate 1.26 mg/ and maximum grain filling rate 2.44 mg/ of T7 were the quickest, and the average grain filling rate 0.94 mg/ and maximum grain filling rate 1.99 mg/ of T12 were the slowest, and the maximum difference percentage of the average grain filling rate and maximum grain filling rate among different density were 33.98%, 22.61%. There was significant correlation between average grain filling rate, maximum grain filling rate, grain filling active duration, rapid increasing stage and thousand grain weight, and the correlation coefficients were 0.628*, 0.630*, 0.849**, 0.739**. Active grain filling duration contributed mostly to TGW.

结果不同密度处理间千粒重、单位面积穗数、穗粒数、单株穗数、单位面积籽粒产量均存在显著差异；不同密度处理冬小麦的籽粒灌浆均符合慢－快－慢的&S&型生长特性，用Richards模型能很好地模拟冬小麦籽粒增重过程，用一元二次抛物线方程能较好地模拟冬小麦灌浆速率随花后时间变化过程；不同密度处理间平均灌浆速率、最大灌浆速率有较大差异，最大差异率分别为33.98%、22.61%，T7的平均灌浆速率1.26mg/及最大灌浆速率2.44mg/均最大，T12的平均灌浆速率0.94mg/及最大灌浆速率1.99mg/均最小；平均灌浆速率、最大灌浆速率、灌浆活跃期、灌浆快增期与千粒重显著或极显著正相关，相关系数分别为0.628*、0.630*、0.849**、0.739**；通径分析表明，灌浆活跃期对千粒重的贡献最大。

Filling in the initial filling valve completely opened up, fast filling; soon to be filling the feed value of filling valve closed to filling in, filling in; to be filling in the feed value filling valve closed valve is opened slowly filling material until the goal of filling weight.

在灌装初始时灌装阀全部打开，进行快灌装；待灌装至快进料值时灌装阀关闭至中灌装位，进行中灌装；待灌装至中进料值时灌装阀关闭，慢灌装阀打开灌装副料直至目标重量。

As for the mesh screen type, its volume multiplied by 100% its porosity was the desirable filling amount. Having considered the forgoing findings, the researchers add up the amounts of the above two types as the filling amount of the composite micro structure, with the filling fluid being acetone. In fabricating the heat spreader, a copper pipe is added to serve the filling purpose. What is more, because the manufacturing process is not carried out in a totally clean environment, there is some noncondensible gas left, which will have a negative effect on the performance of the heat spreader. Consequently, the copper pipe has to be reserved so that the exhaust gases can be evacuated after the filling is done.

Kempers 文中可知，沟槽结构之填充量以微结构体积之80%为最佳，网格结构则是以网格体积乘上孔隙率(porosity，φ)之100%为最佳，故本研究便以两者之加总做为复合式微结构之填充量，填充液为丙酮；在均温基板之制造程序中，会加装一铜管做充填之用，且而由于制造过程并非于一完全干净之环境下完成，故板内会有一些不利于均温基板作用之非凝结性气体noncondensible gas (NCG残留，因此铜管需保留一定的长度，以方便充填完成后将废气排出之用。

与filling-in相关的网络解释 [注：此内容来源于网络，仅供参考]

Raul：劳尔

西 前锋 7 劳尔(Raul) 西班牙 77.06.27 皇马B队 17 范尼() 荷兰(E) 76.07.01 曼联 20 伊瓜因(ín) 阿根廷(E) 87.12.10 河床 9 萨维奥拉() 阿根廷 81.12.11 巴塞罗那 2006-2007赛季西班牙甲级联赛:皇家马德里 成立时间:1902年 上赛季名次:第2名 主场:伯纳乌 (78500人) 主席:卡尔德隆() 主帅:卡佩罗(),

filling core：埋入砂心(铸造)

"注油盒","filling chamber" | "埋入砂心(铸造)","filling core" | "注油杯","filling cup"

rectangle filling：矩形填充

扫描填充:scan filling | 矩形填充:rectangle filling | 填充域:region filling