filling station

filling station的基本解释

n.

汽车加油站

与filling station相关的网络例句 [注：此内容来源于网络，仅供参考]

Result Richards Model and Monodic Quadratic Equation could properly describe grain dry matter growing process and the change process of grain filling rate with days after anthesis. There was big difference in average grain filling rate, maximum grain filling rate under different planting density. Average grain filling rate 1.26 mg/ and maximum grain filling rate 2.44 mg/ of T7 were the quickest, and the average grain filling rate 0.94 mg/ and maximum grain filling rate 1.99 mg/ of T12 were the slowest, and the maximum difference percentage of the average grain filling rate and maximum grain filling rate among different density were 33.98%, 22.61%. There was significant correlation between average grain filling rate, maximum grain filling rate, grain filling active duration, rapid increasing stage and thousand grain weight, and the correlation coefficients were 0.628*, 0.630*, 0.849**, 0.739**. Active grain filling duration contributed mostly to TGW.

结果不同密度处理间千粒重、单位面积穗数、穗粒数、单株穗数、单位面积籽粒产量均存在显著差异；不同密度处理冬小麦的籽粒灌浆均符合慢－快－慢的&S&型生长特性，用Richards模型能很好地模拟冬小麦籽粒增重过程，用一元二次抛物线方程能较好地模拟冬小麦灌浆速率随花后时间变化过程；不同密度处理间平均灌浆速率、最大灌浆速率有较大差异，最大差异率分别为33.98%、22.61%，T7的平均灌浆速率1.26mg/及最大灌浆速率2.44mg/均最大，T12的平均灌浆速率0.94mg/及最大灌浆速率1.99mg/均最小；平均灌浆速率、最大灌浆速率、灌浆活跃期、灌浆快增期与千粒重显著或极显著正相关，相关系数分别为0.628*、0.630*、0.849**、0.739**；通径分析表明，灌浆活跃期对千粒重的贡献最大。

Filling in the initial filling valve completely opened up, fast filling; soon to be filling the feed value of filling valve closed to filling in, filling in; to be filling in the feed value filling valve closed valve is opened slowly filling material until the goal of filling weight.

在灌装初始时灌装阀全部打开，进行快灌装；待灌装至快进料值时灌装阀关闭至中灌装位，进行中灌装；待灌装至中进料值时灌装阀关闭，慢灌装阀打开灌装副料直至目标重量。

The objectives of this paper were to investigate the simulation and design of continuous multiple-station rolling forming process for a U-Section Steel Bar by CAE software-DEFORMTM Due to the limitation of elements number using a short strip 120mm went through all the stations to simulate the real continuous rolling forming on factory The roller gap was fixed as 0 30mm roll speed was 20 rad/sec and progressive angles were all equal for each rolling process which were the formed angle divided by by the number of station Three rolling processes were selected with 6 9 and 12 stations respectively During simulation processes two cases occurred Case A the strip was through a single station Case B the strip across two stations Because the strip laterals side was stretched and twisted during the process The model of case B closer to the practical process than case A and the calculated stress and strain on the tip of U section for case A were lower than these for case B by up to 15% From the result of case B for each process the stress for 12-station process was smallest 9-station process second and 6-station process next Because less-station can save larger cost and forming time but the bigger stress and strain for 6-station caused wrinkles on lateral sides not found on 9-station and 12-station Therefore 9-station process was a more suitable design than 12-station process smaller stretched and twisted and stress The progressive angles for 12-station was 7 5?

本文主要是以DEFORMTM有限元素软体模拟U型钢片连续道次成型与单一道次成型以确认单一道次模拟的是否可取代连续道次模拟之研究。因DEFORMTM 软体对於网格元素上的限制故使用较短素材120mm通过所有的成型站以模拟工厂实际连续成形方法。辊轮间隙固定为0 3mm；辊轮转速为20 rad/sec；弯曲角度的方法为将成型角度平均除以成型站数。有三种辊轮成型方式被选择分别为6站，9站，与12站。在模拟的过程中有两种现象会产生 Case A，素材通过单一成型站。Case B，素材会通过两个成型站。因为在模拟过程中素材的两端会有拉应力与扭力。Case B的模拟比Case A像实际的制程，并计算应力与应变在U型断面的Tip部中可发现Case A比Case B低约15%。从Case B的每站的结果可以得知，12站的成型应力最小，9站次之，6站最后。

与filling station相关的网络解释 [注：此内容来源于网络，仅供参考]

Filling Station：加油站

加油站在美国的叫法有多种,直译成中文的有:汽油站(Gas Station)、燃料站(Fuel Station)、加油站(Filling Station)以及服务站(Service Station)等. 在美国公众中"服务站"(Service Station)已是一个琅琅上口的叫法,作为"加油站"的代名词被广泛认可和接受. .

Filling Station：汽车加油站

filligree 细丝工艺 | filling station 汽车加油站 | filling 填补物

Filling Station：加油站 石油名词

extraction 萃取 石油名词 | filling station 加油站 石油名词 | flash point 闪火点 石油名词

Filling Station：填补中心

Lost and Found 失物招领处 | Filling Station 填补中心 | Shooting Prohibited 禁止射击

petrol filling station：加油站

petrol 汽油 | petrol-filling station 加油站 | petrolatum 矿脂