envelope holder

与envelope holder相关的网络例句 [注：此内容来源于网络，仅供参考]

The LMD algorithm uses extrema to define the local mean and envelope, then to smooth the mean and envelope. To decrease errors in the smoothing process by using moving averaging, a new local mean and envelope definition method (the spline-based LMD) is proposed. The upper envelope and the lower envelope are obtained by connecting the local maxima and the local minima using a cubic spline line. The local mean is defined as a mean of the upper envelope and the lower envelope. A nonlinear simulation signal and a practical vibration signal are decomposed by the LMD and the spline-based LMD.

LMD算法用极值点来定义局部均值函数和局域包络函数，然后用滑动平均来平滑均值和包络函数，针对用滑动平均平滑均值和包络函数误差较大的缺点，提出了采用三次样条对上、下极值点分别插值求得上下包络线，然后由上下包络线的平均获得局部平均函数，由上下包络线相减的绝对值获得局部包络的方法。

Trans-Blot Cells and Systems 170-3825 Trans-Blot Cell With Wire Electrodes and PowerPac HC Power Supply, 100120/220240 V, includes 2 gel holder cassettes, buffer tank, lid with power cables, 4 fiber pads, 1 pack precut blot absorbent filter paper (15 x 20 cm), power supply, power cord, instructions 170-3850 Trans-Blot System With Plate Electrodes and PowerPac HC Power Supply, 100120/220240 V 170-3853 Trans-Blot System With Plate Electrodes, Super Cooling Coil, and PowerPac HC Power Supply, 100120/220240 V, includes 2 gel holder cassettes, buffer tank, lid with power cables, 4 fiber pads, 1 pack precut blot absorbent filter paper (15 x 20 cm), power supply, power cord, instructions 170-3910 Trans-Blot Cell With Wire Electrodes, includes 2 gel holder cassettes, buffer tank, lid with power cables, 4 fiber pads, 1 pack precut blot absorbent filter paper (15 x 20 cm) 170-3939 Trans-Blot Cell With Plate Electrodes and Super Cooling Coil, includes 2 gel holder cassettes, buffer tank, lid with power cables, 4 fiber pads, 1 pack precut blot absorbent filter paper (15 x 20 cm) 170-3946 Trans-Blot Cell With Plate Electrodes, includes 2 gel holder cassettes, buffer tank, lid with power cables, 4 fiber pads, 1 pack precut blot absorbent filter paper (15 x 20 cm) Trans-Blot Cell Accessories 170-3912 Super Cooling Coil, required for all high-intensity transfers 170-3913 Gel Holder Cassette, includes 2 fiber pads 170-3914 Fiber Pads, 15.5 x 20.5 cm, 6 170-3920 Trans-Blot Standard Wire Electrode Card, cathode 170-3921 Trans-Blot Standard Wire Electrode Card, anode 170-3922 Trans-Blot Cell Buffer Tank 170-3923 Trans-Blot Cell Lid With Power Cables 170-3943 Trans-Blot Platinum Anode Plate Electrode 170-3944 Trans-Blot Stainless-Steel Cathode Plate Electrode 170-3945 Trans-Blot Plate Electrode Pair, platinum anode and stainless-steel cathode 16 规格:说明: Trans-Blot Plus

电泳转印槽组件 1。缓冲液槽及带有电缆的盖 2。凝胶支架转印夹 3。纤维衬垫 4。电极丝 5。电极板 6。特级冷却芯 Trans-Blot 转印槽是功能灵活的转印设备，可理想地用于多种转印应用。Trans-Blot 转印槽特点包括：*能进行多胶转印，可容纳3 块PROTEAN I xi 凝胶、6块Criterion 凝胶、12块Mini-PROTEAN 3 或Ready Gel 预制胶*多组参数灵活可设，可调节的电压设置（从30 V 的过夜转印到200 V 的1 小时快速实验）*电极间距设置为8 cm 用于标准印迹杂交，或设置为4cm 用于高强度印迹杂交*可选择板式电极：涂有铂金的钛作为正极，不锈钢为负极，能提供高强度电场和比其它电极更高的电流密度。或选择较经济的铂金电极丝*通过特级冷却芯和水循环仪来调节温度―是天然酶（4°C）或高强度转印的理想选择，随着转印时间增加（多达24 小时），不会引起缓冲液耗竭（在高强度转印中必须使用冷却芯，也推荐用于所有板式电极的应用）*带铰链的凝胶支架转印夹能避免滑动，确保凝胶与印迹膜间的紧密接触；每个转印夹都有颜色标记以保证在转印槽中的正确定位 Trans-Blot 转印槽的锁闭凝胶支架转印夹系统。转印夹（1）支撑凝胶（2）印迹膜（3）两侧有纤维衬垫和滤纸（4）确保凝胶三明治内的完全接触。凝胶夹垂直插入缓冲液槽中（5）。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果板料在压边面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈间的平衡块；或者是压边圈的严重变形。

与envelope holder相关的网络解释 [注：此内容来源于网络，仅供参考]

Envelope holder arm：压纸壁

压纸释放杆Release lever | 压纸壁 Envelope holder arm | 装纸标准板Standard board

Envelope holder arm：壓紙壁文化辦公機器

62413壓紙桿文化辦公機器paper holder bail | 62414壓紙壁文化辦公機器envelope holder arm | 62415壓紙釋放桿文化辦公機器release lever