driving spindle

driving spindle的基本解释

-

主动轴

与driving spindle相关的网络例句 [注：此内容来源于网络，仅供参考]

Our major product is belt type spindle for CNC machining center , spindle for drill machine, high-speed direct drive spindle, CTS spindle, spindle for CNC lathe, spindle for grinding machine, customize spindle and repair spindle service.

目前主要生产CNC切削中心机皮带主轴、钻孔机主轴、高速直结主轴、中空出水主轴、CNC车床主轴，磨床主轴等，另外承接非标主轴订制和专业主轴维修业务。

Through the tests on gas driving water and water driving gas, the flow law of gas and water was real-time observed. Mainly based on the test of water driving gas as an example, the development of molding coal sample and NMR triaxial osmoscope was demonstrated. The experiment process of water driving gas and parameters were demonstrated. NMRI images of molding sample in horizontal cross-section along the driving direction were obtained by NMRI instrument. The results from images were analyzed and compared. Some novel laws were obtained as the following:(1) the leading edge of water driving has inconsistency. This certified the important previous conclusion that the storage of methane mainly was absorbed in inner surface of pore from NMRI technique;(2) the existence of dominant driving pathway was tested and the way kept almost fixed. The pathway is apt to exist in the edge of coal samples where pore and fracture fully develop;(3) the variation of water flow determines the transport velocity of leading edge of water driving and it has lag effect;(4) the effectiveness of the first driving is better than the second driving;and (5) the subsequence of water driving gas are from trunk fractures to branch fractures, then to branch pores.

主要以水驱气NMRI试验为例，详细介绍了核磁共振三轴渗透仪和型煤试件的研制，并重点阐述了水驱气试验过程和相关参数，利用NMRI技术实时观测得到了不同时间沿驱替方向型煤试件水平剖面的NMRI成像图，最后对试验结果进行了比较分析，揭示了一些新的规律认识：(1)水驱替前缘具有不一致性，从NMRI试验角度验证了前人甲烷类气体赋存形式主要以吸附在孔隙内表面为主的重要结论；(2)煤试件存在优势驱替路径，且这种优势路径在驱替过程中基本保持不变，水驱气的优势驱替路径易产生在煤试件边缘，即煤孔隙裂隙发育区；(3)水驱流量变化决定了水驱前缘的运移速度，且对水驱气效果具有滞后效应；(4)水驱气初次驱替效果好于二次驱替效果；(5)水驱替气的顺序为：主要大裂隙—周边裂隙—周边孔隙。

RESULTS: The microscopic observation showed chondrocytes in the transducted group proliferated stably, and triangle, and spindle cells were predominant in the seventh passage, accompanied by few long-spindle and root cells. In addition, the cells were of clear appearance and large lucency. However, in the non-transducted group, long-spindle cells were observed in the fourth passage, and almost all cells exhibited long-spindle shape in the fifth passage.

结果：①倒置显微镜观察，转导组兔关节软骨细胞生长增殖稳定，至第7代仍旧以三角形、梭形及纺锤形细胞为主，偶见长梭形和树根形细胞，且轮廓清晰，透亮度大，折光性强；而未转导组细胞培养至第4代时即己出现长梭形细胞，自第5代细胞形态几乎全部变成长梭形。

与driving spindle相关的网络解释 [注：此内容来源于网络，仅供参考]

spindle footstep：锭脚

spindle driving by gearing 锭子齿轮传动 | spindle footstep 锭脚 | spindle guiding 锭子引导

driving shaft：驱动轴传动轴

driving shaft 驱动轴;主动轴 | driving shaft 驱动轴传动轴 | driving spindle 传动轴

driving spring：主动弹簧,传动弹簧

driving spindle ==> 主动轴 | driving spring ==> 主动弹簧,传动弹簧 | driving sprocket wheel ==> 织链轮