die block
- die block的基本解释
-
-
滑块, 模块, 模具坯料, 底模
- 更多网络例句与die block相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Source of aluminum model: self-check die-block equipped by DPX-MD dual-energy X-ray bone densometer produced by American LUNAR Company; three centrums were obtained from a 38 years old healthy male, a 40 years old osteoporosis male, and a 62 years old osteopenia female. One dead vertebral body was provided by Human Anatomy Laboratory of North Sichuan Medical College.
实验材料:铝体模为双能X射线骨密度仪所配备的自检模块;3个活体椎体分别来源于38岁骨密度正常男性,40岁骨质疏松症男性,62岁轻微骨量减少女性,均为自愿参与实验的川北医学院附属医院医生;1个带软组织的死体椎体,由川北医学院人体解剖实验室提供。
-
Bulk volume of the volume of block block block caliper micrometer-specific block, such as special types of straight shank drill bits Serratula straight shank long twist drill set, such as alloy straight shank twist drill reamer type of hand reamer straight shank straight shank machine reamer taper shank machine reamer and other types of coarse tooth cutter straight shank cutter tooth taper shank Rough Milling fine-tooth cutter straight shank end mill, such as hand-tap machine tap tap tap left teeth straight pipe tap, such as garden die die die left teeth straight pipe die die US-made of other alloys such as Alloy blade machine Segment saw blade, such as gear type inverted roller gear Gear planing cutter knife disc-shaped gear gear shaper cutters, such as factory outlets: cast iron flat, square boxes, granite slab, square and so on.
量块 散量块卡尺专用块千分尺专用块等钻头类直柄麻花钻直柄长麻花钻镶合金直柄麻花钻等铰刀类直柄手铰刀直柄机用铰刀锥柄机用铰刀等铣刀类粗齿直柄立铣刀粗齿锥柄立铣刀细齿直柄立铣刀等丝锥手用丝锥机用丝锥左牙丝锥直管丝锥等板牙园板牙左牙板牙直管板牙美制板牙等其他合金刀头合金刀片机用锯条等齿轮倒类齿轮滚刀齿轮刨刀齿轮铣刀盘形插齿刀等厂家直销:铸铁平板、方箱、花岗石平板、直角尺等。
-
The simulation results of the cylinder-block model were given in the article, consistent with that of Middlemen"s. It was shown that the block part could improve the uniformity of the flow distribution. The analysis of the flow field of some materials with different power-law factor in the die designed by Mckelvey was close to that of Mckelvey"s. It was shown that the flow distribution was uniform in the die that can producesheets with 1200mm in width. During the analysis the flow channel was divided into several parts to get the details about the fluid flow in each area. A conclusion was drawn after analyzing the influence of the die pressure on the flow distribution, that the higher pressure is good for the output and bad for the uniformity of the distribution. Simulation of the die applying the cylindrical main runner showed the fact that when the cylinder replaced the cone the change of uniformity was trivial. The uniformity of the non-block flow channel was so poor that the block in the proper position of the die channel was necessary. The project of the die for the wider sheet was put forth, and the analysis of the fluid flow in the die was shown.
本文模拟了圆柱管缝隙流模型的三维流动场,得到了与Middlemen结论一致的流动均匀性,并通过模拟直观地展示了采用阻尼块可以改善挤出均匀性的现象;分析了多种幂率指数的流体在Mckelvey等人设计的流道模型中的流动分布,得到了与Mckelvey的分析结果接近的压力降和流量偏差;本文建立了1200mm幅宽机头流道的三维有限元模型,并逐个分析各个区域和多个截面的流动分布状况,由此揭示了1200mm幅宽L-型机头流道内的流北京化工大学硕士学位论文动分布基本均匀,并在分析了机头压力对于挤出流动分布的影响后得出结论:较高的机头压力可以获得较大的产量,但是不利于物料均匀分布;模拟了采用圆柱管主流道时机头流道内的流动分布,得出结论:主流道由圆锥管改为圆柱管时对流动均匀性影响不大,通过设置适当的阻尼仍然可以达到挤出平衡;模拟了两端进料式圆柱管无阻尼流道的流动均匀性后得到结论:两端进料式无阻尼结构的流动均匀性较差,宽机头中仍然有必要设置阻尼块;确定宽幅机头流道的基本方案,并设计了一种宽幅防水卷材挤出机头流道的结构,通过流动模拟表明该种结构的流动均匀性较好;考察了宽幅机头对于不同厚度片材的挤出适应性,得到结论:当生产不同厚度的片材时,阻尼块高度需要调整。
- 更多网络解释与die block相关的网络解释 [注:此内容来源于网络,仅供参考]
-
cutting die, blanking die:沖裁模die block模塊
thickness gauge厚薄規 | cutting die, blanking die沖裁模die block模塊 | folded block折彎塊
-
die block hardener:冲模硬化剂
die block ==> 模度坯料,模具坯料,模块,模座,底模,胎模,凹模固定板,板牙 | die block hardener ==> 冲模硬化剂 | die body ==> 模体
-
pipe die block:管子板牙
轻型板牙light-duty die block | 管子板牙pipe die block | 机制板牙 machined die block