deform [di'fɔ:m]

deform的基本解释

vt.

使残缺, 使变形

• Heat deforms plastics.
• 热使塑料变形。

• Her face was deformed by anger.
• 她气得脸都变形了。

vi.

变形

deform的同义词

v. mar · disfigure · blemish · spoil · distort

deform的反义词

vt. embellish · beautify

与deform相关的网络例句 [注：此内容来源于网络，仅供参考]

This paper presents the method of curve deform which is based on the concept of the energy of deform curve.

本文提出了基于变形曲线能量的概念，进行曲线相似变形的方法。

High-density material lying at the circumference of a proacrosomal vesicle was arched with a gap in Solen grandis, but round in Solen strictus. From this gap a proacrosomal vesicle of Solen grandis began to invaginate and deform while it moved to the nuclear front. However a proacrosomal vesicle of Solen strictus did not deform until it reached the nuclear front.

大竹蛏精细胞前顶体囊的高电子密度物质分布在周缘呈一个带缺口的弧形而不是圆形，而长竹蛏前顶体囊周缘的高电子密度物质呈一圆形分布；大竹蛏的前顶体囊是先内凹变形，然后一边变形一边移动，而长竹蛏的前顶体囊是在到达核前端后才开始变形。

The results show that dynamic softening is easy to occur in these ingots and flow stress becomes steady finally; the material constants of hot deformation are procedural parameters that stress-level coefficient α, strain rate sensibility exponent m and deformation activation energy Q are all increased with strain increasing, while stress exponent n is decreased gradually; the values α and m of the alloy homogenized are the biggest and the value n is the smallest, dynamic softening effect of the alloy is the most obvious, which can deform evenly; influence of strain on the value Q of the alloy homogenized is a little and the average value of Q is only 176.5kJ/mol, so the alloy is easy to deform; the alloy matrix shows the regular recrystallization grains when the strain is 50%; dislocation cell structure re-formed in the grains with increase of strain.

结果表明：经不同处理的Al-1Mn-1Mg合金均易发生动态软化并最终呈现稳态流变特征；热变形材料常数是过程量，随应变量的增加，应力水平参数α、应变速率敏感性指数m和热变形激活能 Q 随之增大，而应力指数 n 则逐渐减小；均匀化退火后，铝合金的α和m值最大而n值最小，动态软化效果最明显且变形均匀，在该状态下，铝合金的 Q 值受变形量影响小，平均仅为176.5kJ/mol，易进行热变形；当应变量为0.7时，基体呈现规则的再结晶晶粒组织，随着应变量的增加，晶内重新形成了位错胞结构。

与deform相关的网络解释 [注：此内容来源于网络，仅供参考]

Deform：变形

第一节 档案(File)菜单第二节 编辑(Edit)菜单第三节 检视(View)菜单第四节 选取(Pick)菜单第五节 复制(Copy)菜单第六节 变形(Deform)菜单第七节 曲线(Curve)菜单第八节 曲面(Surface)荣单第九节 杂项(Misc)荣单第十节 帮助(He

Deform：软件

环境定性的分析切削热,并利用通用有限元软件(DEFORM)举行建模分析,给出一种直不雅的温度场漫衍状况. 最后接纳纯一变量法,求出切削温度关于转速、进给量的瓜葛式,应用Matlab编程,作出前刀面最高切削温度与转速、进给量的变化曲线.

Deform：使不成形,使丑

deflect 使偏斜,使转向 | deform 使不成形,使丑 | defraud 欺骗,诈欺

Deform：(使)变形

deflect#使偏离 | deform#使变形 | defraud#欺诈

Surf Deform：<表面变形编辑器>

Path Deform | Surf Deform | * Surf Deform