cylinder bore

cylinder bore的基本解释

-

[机] 气汽缸内径

与cylinder bore相关的网络例句 [注：此内容来源于网络，仅供参考]

Cylinder, the cylinder sets of radial a surplus deformation of the cylinder sets a great impact on the cylinder liner reduced radial a surplus amount to reduce the deformation of the cylinder sets, the top surface of the body decreases roughness, but it will increase the body on the plane cylinder only mouth the roughness ; Preload reduced cylinder head bolt deformation of the cylinder liner little effect, the body can reduce the top surface roughness and cylinder body on the plane I ended roughness; Shen appropriate reduced cylinder head bolt hole deep can reduce the deformation of the cylinder sets, but will cause the body and the top surface roughness on the cylinder body only I roughness increases Plane .

工作工况下，对于第2缸来说，气缸套径向过盈量对气缸套变形影响很大，减小气缸套径向过盈量，有利于减小气缸套的变形，减小机体顶面不平度，但会增大机体上缸套止口平面的不平度；减小缸盖螺栓预紧力对气缸套变形影响很小，可减小机体顶面不平度和机体上缸套止口平面的不平度；适当减小缸盖螺栓沉孔深可以减小气缸套的变形，但会造成机体顶面不平度和机体上缸套止口平面不平度的增大。

Caused by disc brake on the brake Wheel Cylinder could not return to places 4 possible: First, 5 foot brake valve exhaust port blocking, high-pressure gas instinct platoon atmosphere, caused by gas-liquid master cylinder of the spring could not return to place, resulting in the system move oil, brake disc brake Wheel Cylinder Piston top dead and could not return to places; second is to the disc brake master cylinder gas-liquid pipeline blockage, resulting in brake Cylinder piston can not return to place; third master cylinder of the gas-liquid Spring itself can not return to position, brake fluid under high pressure gas can not return Axial pump to gas-liquid master cylinder reservoir chamber, resulting in brake Cylinder piston can not return to places; Fourth Wheel Cylinder piston disc brake system, due to moving fluid dirty or rusty card dead and can not return to the piston position.

造成盘式制动器上的制动分泵不能回位有4种可能：一是脚制动阀5的排气口堵塞，高压气体本能排人大气，造成气液总泵的弹簧不能回位，导致制动油将盘式制动器的制动分泵活塞顶死而不能回位；二是气液总泵至盘式制动器的油管堵塞，造成制动分泵活塞不能回位；三是气液总泵的弹簧本身不能回位，制动液在高压气体作用下，不能回到气液总泵的储油室，从而造成制动分泵活塞不能回位；四是盘式制动器制动分泵活塞由于制动液太脏或活塞生锈卡死而不能回位。

Caused by the brake disc brake on back wheel should not have four kinds of spaces possible: First, the foot brake 5 exhaust inlets, high pressure gas instinct Pai people the atmosphere, caused by gas-liquid master cylinder should not spring back to place, cause the system Oil will move the brake disc brake wheel cylinder piston top dead can not come back to places; are gas-liquid two disc brake master cylinder to the tubing plug, resulting in brake wheel cylinder piston can not come back to places; are three master cylinder of gas-liquid Can not spring back to their own spaces, brake fluid under high pressure gas, liquid should not return to the master cylinder reservoir chamber, resulting in brake wheel cylinder piston can not come back to places; are four wheel disc brake piston brake system because of moving fluid dirty or rusty Pistons Can not Back-bit card dead.

造成盘式制动器上的制动分泵不能回位有4种可能：一是脚制动阀5的排气口堵塞，高压气体本能排人大气，造成气液总泵的弹簧不能回位，导致制动油将盘式制动器的制动分泵活塞顶死而不能回位；二是气液总泵至盘式制动器的油管堵塞，造成制动分泵活塞不能回位；三是气液总泵的弹簧本身不能回位，制动液在高压气体作用下，不能回到气液总泵的储油室，从而造成制动分泵活塞不能回位；四是盘式制动器制动分泵活塞由于制动液太脏或活塞生锈卡死而不能回位。

与cylinder bore相关的网络解释 [注：此内容来源于网络，仅供参考]

cylinder bore：缸径

cylinder body 缸体 | Cylinder bore 缸径 | cylinder head 汽缸盖

cylinder bore：汽缸内径

cylinder block 汽缸排 | cylinder bore 汽缸内径 | cylinder bore gage 汽缸内径规

cylinder bore：缸内径

1656 缸体 cylinder block | 1657 缸内径 cylinder bore | 1658 缸底 cylinder bottom

cylinder bore：缸套

卷筒:Coiler cylinder | 缸套:cylinder bore | 拉缸:cylinder scoring

cylinder bore gauge：量缸表,缸径测量仪

cylinder-bore ellipticity 气缸椭圆度 | cylinder bore gauge 量缸表,缸径测量仪 | cylinder capacity 气缸工作容积