cubic effect

cubic effect的基本解释

-

立体感

与cubic effect相关的网络例句 [注：此内容来源于网络，仅供参考]

Using of optical microscopy, X-ray diffraction, transmission electron microscopy, hardness and tensile testing, the effect of thermal exposure at high temperatures on the microstructures and of high-temperature tensile properties of rapidly solidified AlCrYZr have been studied. The results show that there are two main phases,Al20Cr2Y(cubic, a=1.437 nm) and DO23Al3Zr(terganal, a=0.4 013 nm , c= 1.732 nm), in the as-solidified alloy. The Al20Cr2Y phase can maintain its cubic structure at 500℃, but the particles coarsen remarkably and even become lumpish. In coarse lumpish Al20Cr2Y phase the plane faults and twin structures exist.

摘 要：采用金相、 X射线衍射、透射电镜、硬度测定和拉伸试验研究了高温热暴露对快速凝固AlCrYZr合金显微组织影响和高温下力学性能的热稳定性，结果表明，快速凝固AlCrYZr合金主要第二相为Al20Cr2Y(立方，a=1.437nm)和DO23Al3Zr(正方，a=0.401 3nm， c=1.732nm)，Al20Cr2Y在500℃热暴露尚能保持其立方结构，但质点明显粗化，甚至块状化，在粗大的Al20Cr2Y相中存在有层错和孪晶结构。

The results were found as following:(1) The damage value increases more significantly with the increase in PVF before 30% PVF, beyond which the increasing trend becomes gradually gentle.(2)Keeping the interphase strength and PVF unchanged, the damage increase with increasing moisture concentration in a nearly linear relation.(3)The results generated from the FCC model with consideration of the interphase debonding are in good agreement with the experimental data, meanwhile, the FCC model is also capable of predicting the critical load for the damaged and the undamaged dental composite subject too the 3-point flexural test.4 A 3D-fmite element analysis has been successfully exploited to examine the mechanical behavior of the restoration-tooth structure under the polymerization shrinkage and water sorption. It was found:(1) The low stiffness of the composite has the effect to limit the displacement occurring in the remaining tooth tissue. For lower interphase, the cuspal flexures are litter higher. The high interphase modulus acts as a \'shielding effect\' for stress transfer.

得到如下结论：(1)相同的吸湿性，在30％PVF(颗粒体积分数：Particle volume fraction，PVF)前增加PVF，层间脱胶损伤值显著增加；此后损伤值的增加趋于平缓；(2)保持层间强度和PVF不变，层间脱胶损伤随吸湿率的增加而接近线性增加；(3)FCC(面心立方：Face-centred cubic，FCC)模型层间脱胶损伤的预测结果和实验数据基本吻合；同时此模型可以用于预测牙齿填充材料三点弯曲实验的临界载荷。4、建立理想牙齿修复结构，利用有限元方法研究了同时考虑聚合收缩和吸湿膨胀耦合作用下的填充修复材料和粘结界面层材料性能对牙齿修复结构的力学行为的影响，得到如下结论：(1)低弹性模量的牙齿填充修复材料能限制天然牙组织的位移，但天然牙组织的位移与粘结界面层的弹性模量无关。

After filtration of the air into a cold wind into the interior and motor in the 1.1 kilowatts, resulting from the effect of wind pressure 180Pa and 18,000 cubic meters per hour of air volume, the interior has the original foul smell of the hot air discharged through the doors and windows to achieve the cool, filter dust, ventilation, improve the efficiency of the effect of workers.

过滤后的空气变成冷风送入室内并在1.1千瓦电机的作用下形成180Pa的风压和每小时18000立方米的风量，将室内原有的污浊有异味的热空气通过门窗排出，从而达到降温、过滤风尘、通风换气、提高工人效率的效果。