crucible tongs

crucible tongs的基本解释

-

坩埚钳

与crucible tongs相关的网络例句 [注：此内容来源于网络，仅供参考]

The tongs all passes in the machine the gearing on the bed what tongs the gearing on realizes with superficial contact in the cowgirl on the bed in machine or matches.when the tongs installs in the machine bed work on the stage,the center of gravity of the tongs should be as far as possible low,center of gravity the more high an accepts should the dint is more big,the tongs bottom four directions should bulge,make its contact good,or the bottom establishes four a feets.when the tongs installs on the machine bed principal axis,the tongs install the to should have the enough match accuracy with principal axis cowgirl surface,and guarantee the gearing the stability dependable.

夹具体在机床上的安装都是通过夹具体上的安装基面与机床上的相应表面的接触或配合实现的。当物流设备需要的公司体在机床工作台上安装时，夹具的服装厂应尽量低，重心越高则支承面应力越大，夹具底面四边应凸出，使其接触良好，或底部设置四个支脚。当夹具体在机床主轴上安装时，夹具安装基面与主轴相应表面应有足够的配合精度，并保证安装稳定可靠。

This text is divided into seven greatest parts totally, the first part is the analysises of the combined part of technic and construction; The second part is a coordination to combined part project design;The third part is the project reasoning of the assemble tongs, synthesizing the consideration with the economic angle and the technique,choice a reasonable and oecumenical design project of the assemble tongs;The fourth part is design of assemble tongs for combined part, primarily discussing the choice of framework、localizer and clamp;The fifth part is the instruction of assemble tongs in the combined part assemble;The sixth part is the instruction of technique term and actual technique problems handles in the design; The seventh part is the design of the

本文共分七大部分，第一部分是组合件的结构及工艺性分析；第二部分是组合件的协调方案设计；第三部分是组合件装配型架的方案论证，从技术和经济角度综合考虑，选择合理、经济的型架设计方案；第四部分是组合件的装配型架设计，主要论述了骨架，定位件和夹紧件的选择；第五部分是介绍了组合件装配型架的安装；第六部分是组合件装配型架的设计技术条件及实际技术问题的处理；第七部分钣金件加工设计。

So, using magnesia and calcia crucible in VIF respectively, the experiments on deep deoxidation by carbon and the phenomenon of oxygen contamination from crucible materials in the molten steel under some temperature and vacuity and oxygen content of the molten steel were made and it were found that properly low melting temperature and vacuity helped to lighten and even avoid oxygen contamination from crucible material and the refining effect of final oxygen content of 5×10-4% in the molten steel was achieved using calcia crucible with better resistance to thermal shock under higher vacuity.

为此，分别采用MgO炉衬与CaO炉衬，在真空感应炉中对钢液用碳进行深脱氧和炉衬供氧现象实验研究，发现：(1)在适当低的熔炼温度和真空度下，可以减轻甚至避免炉衬热分解向钢液供氧；(2)采用热稳定性优越的CaO炉衬，在较高的真空度下可达到钢液最终全氧含量低于5×10-4%的精炼效果。

与crucible tongs相关的网络解释 [注：此内容来源于网络，仅供参考]

crucible steel process：坩埚炼钢(法)

crucible steel | 坩埚钢 | crucible steel process | 坩埚炼钢(法) | crucible tongs | 坩埚钳

crucible tongs：坩蜗钳

坩蜗炉 crucible furnace | 坩蜗钳 crucible tongs | 坩蜗涂浆 crucible wash

crucible furnace：坩蜗炉

坩蜗浇铸装置 crucible pouring device | 坩蜗炉 crucible furnace | 坩蜗钳 crucible tongs