crevice ['krevis]

crevice的基本解释

n.

裂缝

crevice的同义词

n. cleft · fissure · crack

与crevice相关的网络例句 [注：此内容来源于网络，仅供参考]

In borate or phosphate buffered NaCl solutions with a constant total concentration of borate or phosphate, E_ increases with an increase in pH. With the increase of the concentration of chloride ions, E_ decreases markedly in the test solutions. Moreover, the buffer capacity and concentration of nonaggressive anions in the test solutions also exerts some effects on the crevice corrosion of Type 304 stainless steel. Furthermore, the cooperative inhibition effect of the environmental factors on crevice corrosion was investigated. The potential of crevice corrosion E_(cc shows a strong dependence on a parameter J, which was called as general environmental factor and defined as the product of concentration of nonaggressive anions, pH, buffer capacity and concentration of chloride ions.

在含NaCl 的硼酸或磷酸盐缓冲溶液中，在相同的缓冲溶液总浓度下，E_c随pH 值增加而增加；但随着氯离子浓度的增加，E_c显著降低；另外缓冲容量及其阴离子对304 不锈钢缝隙腐蚀也有影响；最后实验研究了这些环境影响因素的协同影响规律，得出环境综合影响因素参数J，J 由pH 值、缓冲容量、氯离子浓度及其缓冲溶液中其它阴离子浓度定义，缝隙腐蚀电位与参数J 有好的线性关系。

A simulated crevice corrosion cell was used to study the anolyte within crevice of Steel Cr18Ni9Ti in 3% NaCl sulotion.

采用摸拟缝隙的闭塞电池研究了0Cr18Ni9Ti 奥氏体不锈钢在3%氯化钠溶液中闭塞区内溶液的变化和 Cr存在的形态。

The crevice corrosion rate of 00Cr25Ni22Mo2 in oxidative medium is much greater than that in reductive medium, but the law for titanium quite the rev erse. There is much effect of temperature on the crevice corrosion rate.

结果表明：在有缝隙的情况下， 00Cr25Ni22Mo2不锈钢在氧化性介质中的缝隙腐蚀速率明显大于在还原性介质中的缝隙腐蚀速率；工业纯钛则恰恰相反。

与crevice相关的网络解释 [注：此内容来源于网络，仅供参考]

crevice：裂缝

组成酶活性中心的氨基酸残基的侧链在一级结构上可能相距很远,甚至可能位于不同的肽链上,经肽链的盘绕折叠,而在空间构象上互相靠近进入适当位置形成活性区域. 这个区域是位于酶分子表面的一个裂缝(crevice)内.

crevice：裂隙,裂缝

crescograph 植物生长描记器 | crevice 裂隙,裂缝 | cribral 筛状的

crevice：裂隙[可用于描述生物大分子的立体结构]

cresol purple 甲酚紫 | crevice 裂隙[可用于描述生物大分子的立体结构] | crinophagy 分泌自噬

crevice：细缝

scrub:擦 | crevice:细缝 | dislodge: 去除; 取出

crevice corrosion：缝隙腐蚀

中国钢铁研究总院与瑞典腐蚀研究所共同开展了汽车及其用材的腐蚀与对策研究.合作研究涉及中国、瑞典汽车腐蚀现状调查;汽车用金属及其涂层材料在各种气候环境下的耐蚀性能;汽车腐蚀重要类型-穿孔腐蚀(Perforation Corrosion)和缝隙腐蚀(Crevice Corrosion)的微观机理以及汽车