conical helix

conical helix的基本解释

-

锥形螺旋线

与conical helix相关的网络例句 [注：此内容来源于网络，仅供参考]

In different conditions on fluidized state and stability of conical fluidized bed. The conlusions are: the conical angel of the conical fluidized bed is 20°, the fluidized state havesmall difference in conical distributor and distributor plate. The angle of conical bed increase,the fluidized state will have big difference. The angle is 60°and the conical as distributor, themass of fluidized is less, the most of material is the bottom of conical bed. The effect ofdistributor plate is much better than the conical distributor. Sawdust and rice hull can fluidize.The annular gap of conical distributor different, the angle of conical bed is same, the fluidizedquality of 10mm annular gap is better than the other conical distributors. The annular gap ismore wide, the conical bed have more slugging phenomenon and the pressure fluctuate is turnbig.In the experiment the flow of 2％and 4％distributor plates don\'t easy to control, becausethe pressure is very big and the pressure fluctuate of conical bed is too big.

在不同的条件下对锥形床的流化状态和稳定性进行了研究，结果得出：锥形床的锥角为20度时，分布锥和分布板的流化状态相差不明显，随着锥形床锥角的增大，分布锥和分布板的流化现象会出现明显的变化，锥形床锥角越大，分布锥的流化状态变化越明显，流化的的物料越少，大量物料都聚集在锥形床底部，而分布板在加料量少的情况下，能流化起来。10mm、15mm和20mm环隙分布锥在锥形床锥角相同条件下，10mm环隙分布锥的流化质量要好于其它两个分布锥，环隙越大越容易出现腾涌现象的产生，压降波动范围增大。2％、4％和6％开孔率分布板在本实验测定时，2％和4％开孔率分布板的流量不容易调节，同时产生的压降波动范围也很大，比较来说，6％开孔率分布板流化质量好些。

This method undertakes comparative getting the area between the spare parts to equation of geometry of the face in model of CAD of different spare parts above all - surface contact relation and type, use amount coming back theory general face - the face expresses to be helix; relative to instantaneous motion next, the helix that goes up to many surface contact undertakes making operation,; of helix of the motion when making the opposite very short time between the spare parts is final, according to the spare parts abut concern plan and abut spare parts move relatively helix, undertook an analysis to assembling instantaneous of whole of the spare parts in the model to concern with drive movably, give out not between the method of calculation of helix of opposite instantaneous motion between photograph adjacent spare parts and them but the judgement method of drive sex.

该方法首先对不同零件CAD模型中面几何方程进行比较得到零件之间的面-面接触关系和类型，并应用旋量理论将面-面相对瞬时运动表示为螺旋；然后，对多个面接触上的螺旋进行交运算，生成零件之间的相对瞬时运动螺旋；最后，根据零件邻接关系图和邻接零件相对运动螺旋，对装配模型中零件整体瞬时可动性和驱动关系进行了分析，给出不相邻零件之间的相对瞬时运动螺旋计算方法和它们之间可驱动性的判定方法。

On applying the theory of differential geometry, the research shows the procedure for determining the required cutter path for cutting conical cam profile using a NC milling machine based on the analytical profile expression of conical cam with oscillation conical roller follower or with a translating conical roller follower established in 3D space. The analytical expression of cutter path is provided for a tapered endmill cutter, whose size may be identical to or smaller than that of the conical roller.

应用微分几何理论，以在3维空间所建立的圆锥滚子摆动从动件和直动从动件圆锥凸轮机构凸轮廓面的解析表达式为基础，对数控铣床加工圆锥凸轮廓面所需刀具轨迹方程的建立方法进行了研究，根据所采用的锥形刀尺寸等于或小于圆锥滚子尺寸的情况，推导出相应的刀具轨迹方程的解析表达式。

与conical helix相关的网络解释 [注：此内容来源于网络，仅供参考]

conical helix：锥形螺旋线

conical drum 锥形滚筒 | conical helix 锥形螺旋线 | conical mill 锥形球磨机

conical helix：圆锥螺旋线

conic section 圆锥曲线 | conical helix 圆锥螺旋线 | conical surface 锥面

conical helix：圆锥形螺旋线

"圆锥形盘旋面","conical convolute" | "圆锥形螺旋线","conical helix" | "圆锥形斜螺旋体","conical oblique helicoid"

conical helix：円錐

conic section 円錐曲線 | conical helix 円錐らせん | conical horn 円すいホーン

helix,conical：圆锥螺旋线

"螺纹螺旋角","helix angle of thread" | "圆锥螺旋线","helix,conical" | "圆柱螺旋线","helix,cylindrical"