conical bearing

conical bearing的基本解释

-

圆锥轴承

与conical bearing相关的网络例句 [注：此内容来源于网络，仅供参考]

In different conditions on fluidized state and stability of conical fluidized bed. The conlusions are: the conical angel of the conical fluidized bed is 20°, the fluidized state havesmall difference in conical distributor and distributor plate. The angle of conical bed increase,the fluidized state will have big difference. The angle is 60°and the conical as distributor, themass of fluidized is less, the most of material is the bottom of conical bed. The effect ofdistributor plate is much better than the conical distributor. Sawdust and rice hull can fluidize.The annular gap of conical distributor different, the angle of conical bed is same, the fluidizedquality of 10mm annular gap is better than the other conical distributors. The annular gap ismore wide, the conical bed have more slugging phenomenon and the pressure fluctuate is turnbig.In the experiment the flow of 2％and 4％distributor plates don\'t easy to control, becausethe pressure is very big and the pressure fluctuate of conical bed is too big.

在不同的条件下对锥形床的流化状态和稳定性进行了研究，结果得出：锥形床的锥角为20度时，分布锥和分布板的流化状态相差不明显，随着锥形床锥角的增大，分布锥和分布板的流化现象会出现明显的变化，锥形床锥角越大，分布锥的流化状态变化越明显，流化的的物料越少，大量物料都聚集在锥形床底部，而分布板在加料量少的情况下，能流化起来。10mm、15mm和20mm环隙分布锥在锥形床锥角相同条件下，10mm环隙分布锥的流化质量要好于其它两个分布锥，环隙越大越容易出现腾涌现象的产生，压降波动范围增大。2％、4％和6％开孔率分布板在本实验测定时，2％和4％开孔率分布板的流量不容易调节，同时产生的压降波动范围也很大，比较来说，6％开孔率分布板流化质量好些。

The main products include deep groove ball bearing, variation core roller bearing, cylinder roller bearing, british system bearing, variation core ball bearing, double row deep groove ball bearing, pillow block bearing, corner touch bearing, trust roller bearing, tapered roller bearing, and spherical roller bearing.

主营产品包括：深沟球轴承、调心滚珠轴承、圆柱滚珠轴承、英制轴承、调心球轴承、双列深沟球轴承、座架、角接触轴承、推力球轴承、圆锥滚子轴承和球面滚珠轴承。

The assembly of journal and plain bearing liner space is too little, force of organic still oil pressure is small it is the crucial index that affects lubricant result, make lubricate because of lacking engine oil between crankshaft and plain bearing liner and bite dead invalidation, include to be pulled badly, lack lube, layer of alloy of dry attrition generation is fused, grind sliding surface to did not maintain the oily film of certain ply, and all sorts of local overload exhaustion are destroyed, cavitation erosion and V form are destroyed etc, through technology of him director diesel locomotive old experience reachs the analysis of pair of its breakdown reasons, put forward precautionary measures especially. As a result of,the burns caustic mechanism plain bearing liner to burn caustic mechanism of 1 plain bearing liner is the lube film burst between journal and plain bearing liner, cause plain bearing liner and crankshaft generation clash, below high temperature, high pressure and high rotate speed, the wear-resisting alloy layer of plain bearing liner wears away prematurely or fuse, cause plain bearing liner and crankshaft to stick thereby bite, can make the steel back of plain bearing liner and Kong Zhong produces whirligig, inlet port is jammed, carry on the back by steel again with the friction of aperture causes high temperature to make plain bearing liner burned-out further, can cause bolt to break off, happen swing a malign accident that pounds cylinder body of bad internal-combustion engine.

轴颈和轴瓦的装配间隙太小，还有机油压力低是影响润滑效果的关键指标，使得曲轴和轴瓦之间因缺少机油润滑而咬死失效，包括严重拉伤，缺少润滑油，干摩擦产生合金层熔化，磨滑面没有保持一定厚度的油膜，以及各种局部过载疲惫破坏，气蚀和V形破坏等，通过本人主管内燃机车技术多年经验及对其故障原因的分析，特提出预防办法。1轴瓦的烧损机理轴瓦烧损的机理是由于轴颈和轴瓦之间的润滑油膜破裂，导致轴瓦和曲轴产生摩擦，在高温、高压和高转速下，轴瓦的耐磨合金层过早地磨损或熔化，从而引起轴瓦和曲轴粘咬，会使轴瓦的钢背和座孔中产生旋转运动，进油孔被堵塞，再由钢背和座孔的磨擦进一步引起高温使轴瓦烧坏，并会造成螺栓折断，发生甩出捣坏内燃机缸体的恶性事故。

与conical bearing相关的网络解释 [注：此内容来源于网络，仅供参考]

conical bearing：锥形轴承

conical beam 锥形射束 | conical bearing 锥形轴承 | conical bolt 锥形螺栓

conical trommel：锥形滚筒筛

conical roller bearing 圆锥滚柱轴 | conical trommel 锥形滚筒筛 | conical valve 锥形阀

conical beaker：锥形烧杯

conical 圆锥形的 | conical beaker 锥形烧杯 | conical bougie 锥形探条