composites

composites的基本解释

n.

合成物, 混合物, 复合材料( composite的名词复数 )

与composites相关的网络例句 [注：此内容来源于网络，仅供参考]

The results under the oil lubricate friction conditions were similar with those under the dry friction conditions. The wear mechanism of 3Cr13 matrix alloy was micro-cutting and distorting wear. For the composites with a low fraction of TiC particle, distorting wear dominated and cutting was partly operating. For the composites with a high fraction of TiC particle, stress fatigue wear and wear of hard phase decohesion has occurred, but the main wear mechanism was still distorting wear. When the wear experiments were performed under the oil lubricate friction conditions, the main wear mechanism has became to abrasive wear and fatigue wear for the composites with the low TiC fraction, and fatigue wear would be to dominate for the composites with the high TiC fraction. There were similar wear mechanisms in H13 and 1Cr18Ni9 matrix composites.

在干摩擦条件下，3Cr13基体合金的磨损机理为显微切削和变形磨损；低体积分数的复合材料磨损机制以变形磨损为主，兼有少量的切削磨损机制；高体积分数的复合材料磨损机制以变形磨损为主，兼有应力疲劳磨损和脆性相剥落磨损；在油润滑摩擦条件下，3Cr13基体合金的磨损以磨粒磨损为主；低体积分数的复合材料磨损为磨粒磨损和疲劳磨损；高体积分数的复合材料磨损以疲劳磨损为主。H13、1Cr18Ni9基体及其复合材料的磨损机制类似于3Cr13基体及其相同体积分数的复合材料。

The mechanical properties of coal filled polymer composites The mechanical properties of coal/PP composites were investigated, and the effects of coal rank, particle size, surface modification of coupling and alkylation were discussed. The results show that the anthracite and bituminous coal all can be used as filler of plastic after pretreatment of part devolatilization and surface modification; The modulus of composites increase with the content of coal filler; The coupling agent is of no effect for reinforcing the coal/PP composites, except that there are new oxygenous function group forming on the surface in the process of pulverizing; The F-C alkylation reinforce coal (under 10μm)/PP composites obviously.

4煤填充高分子复合材料力学性能超细煤粉填充聚丙烯复合材料力学性能的研究结果表明，烟煤和无烟煤经过脱除部分挥发分的预处理后，都可用于与塑料共混制备复合材料；偶联剂改性对低变质程度烟煤/聚丙烯复合材料的力学性能基本不起改善作用，而对于经气流超细粉碎后的小粒径高变质程度烟煤及无烟煤则有一定的增强作用；烷基化改性在煤表面接枝了烷基，使平均粒径小于10μm的煤/聚丙烯复合材料拉伸屈服强度普遍提高，煤填充高分子复合材料可在较高含煤量情况下维持良好的力学性能。

The results show that the ingather of tungsten in the composites using internal feedstock injection is higher than that of the composites using external feedstock injection. For the composites using IFI method, the influence of input power on the copper oxidation is not evident, while more and more cuprite (Cu2O) is detected with the increasing of input power for the composites using EFI method. The thermal conductivity of WCu composite is lower than the theoretical value by ROM.

结果表明，在内部送粉条件下，复合材料中钨的收得率要高于外部送粉条件下复合材料中钨的收得率；在内部送粉条件下，功率对铜氧化的影响并不明显；而在外部送粉条件下，随着功率的提高，铜的氧化明显增多；由于氧化物和孔隙等的存在，利用大气等离子喷涂工艺制备的复合材料的导热率远远低于根据混合法则计算的理论值。

与composites相关的网络解释 [注：此内容来源于网络，仅供参考]

Elastomeric composites：高弹体复合材料

elastomer 弹性体 | Elastomeric composites 高弹体复合材料 | elastoplasticity 弹塑性

Composites：复合材料

如果用"复合材料"(Composites)这个名词就可以让所有人都可以接受了,因为现在合金钢也被纳入了复合材料的范畴. 而实际上让他们真正明白FRP是很重要的:FRP是由树脂包覆玻璃纤维组成的,玻璃纤维提供FRP的强度和刚性,树脂提供FRP的耐化学性和韧性.

Composites：合成

掌握为不同输出方式预备文档的方法,输出方式包括:分色输出(Seperation)、合成(Composites)输出、打印标记(Printers Marks). 陷印(Trapping)、陷印样式(Trapping Style)和打印机样式(Printer Style)掌握调板、调板浮动菜单和预置选项处理文本的排版,

Composites：复合物

一般而言,生医材料的种类包括:金属、合金、陶瓷、聚合物、生物来源物质以及复合物(composites)等. 临床上使用的生医材料可以分为四大类,分别为:金属与合金材料(metals and alloys)、陶瓷材料(ceramics)、高分子材料(polymers)与生物组织材料(biological materials).

Composites：复合体

composite propellants 复合推进剂 | composites 复合体 | composition board 复合板