coated metal

coated metal的基本解释

-

包镀金属, 被覆金属

与coated metal相关的网络例句 [注：此内容来源于网络，仅供参考]

Disclosed are an adhesive composition for a metal foil which comprises a material wherein a tracking resistance test is carried out according to the IEC method by making a thickness of an adhesive layer 30 to 40 mum, using a copper foil pattern with a width of 4 mm and making a distance between electrodes 0.4 mm, then the adhesive layer dissolves out for the first time when 5 drops or more of an electrolyte are dropped thereon, an adhesive-coated metal foil, a metal-clad laminate, a wiring board, a multi-layer board and a multi-layer wiring board using the same.

本发明公开了一种用于金属薄片的粘合剂组合物，它含有一种材料，其中，抗电弧径迹测试是按照IEC方法进行的，粘合剂层的厚度被做成30至40μm，使用了具有4mm宽度的铜薄片图形，并使电极之间的距离为0.4mm，然后，当5滴或更多的电解液被滴加其上时，粘合剂层被首次溶解掉。使用它的一种粘合剂涂覆的金属薄片，一种金属包覆的层压板，一种多层板和多层电路板。

The theoretical method presented here can be employed to forecast the shift of the resonance wavelength, and to help the design and fabrication of the metal-coated LPFG.

标 签 导波与光纤光学长周期光纤光栅金属包层光纤三层介质光纤包层模 guided wave and fiber optics long-period fiber grating metal-coated fiber three-layered optical fiber cladding modes

The results show that: the tensile strength, flexural strength and flexural modulus increase by about 10.4%, 62.1% and 122.3% respectively when the mass fraction of the aluminum powder increases from 0 to 50%, while elongation at break and impact strength decrease by about 65.0 and 74.4% respectively; the tensile strength, elongation at break and impact strength all increase with decreasing the particle sizes of the aluminum powders.b Nylon-12 coated metal powders for the indirect SLS process were prepared by the dissolution precipitation process. The coated powders have only 1.0 wt% nylon-12, and their SLS green parts have sufficient strength for features as small as 1.0 mm to be built and post-processed and high dimensional accuracy. The green parts were subjected to the post processing processes including binder decomposition and infiltration of epoxy resin, and then the metal/polymer composite parts with relatively high strength and accuracy were formed.At present, micron-scale inorganic fillers have been widely used to reinforce nylon SLS parts.

将该法制备的尼龙12覆膜金属粉末用于以下两个方面：a使用铝粉增强尼龙12的SLS成形件，通过溶剂沉淀法制备尼龙12覆膜铝复合粉末，研究了铝粉含量及粒径对SLS成形件性能的影响，结果表明：铝粉分散均匀，并与基体有良好的界面粘接；当铝粉含量从0增加到50wt％时，成形件的拉伸强度、弯曲强度、弯曲模量分别提高10.4％、62.1％和122.3％，冲击强度和断裂伸长率下降65.0％和74.4％，耐热性及尺寸精度也得到提高；断裂伸长率、冲击强度及拉伸强度均随着铝粉粒径的减小而增大。b使用溶剂沉淀法制备了间接法SLS用尼龙12覆膜金属粉末，该覆膜粉末中聚合物粘接剂的含量仅为1.0 wt％，其SLS初始形坯具有较高的精度以及足够满足后处理要求的强度，最小精细结构的尺寸达1.0 mm。

与coated metal相关的网络解释 [注：此内容来源于网络，仅供参考]

Coated metal head resists rust：覆膜金属头部抗拒锈病

Serrated knife edge to cut through roots and other tough material锯齿刀口,以减少通过根和其他强硬材料 | Coated metal head resists rust覆膜金属头部抗拒锈病 | Limited lifetime warranty有限终身保修

black-coated metal chart：黑色涂层的金属卡片

black-and-white vector 黑白向量 | black-coated metal chart 黑色涂层的金属卡片 | black-lead 石墨

metal-coated surface：表面金属化

覆膜金属粉末:polymer-coated metal powder | 表面金属化:metal-coated surface | 镀铜石墨粉:copper coated graphite