chill mold

chill mold的基本解释

-

[机] 冷硬模

与chill mold相关的网络例句 [注：此内容来源于网络，仅供参考]

We are specialized in manufacturing various plastic mold such as automotive lamp mold, bumper mold, instrument panel mold, automobile handle, auto interior decoration mold, TV mold, air-condition mold, washing machine mold, air-auxiliary mould, garbage bin mold, plastic chair mold, etc.

浙江省台州市金典模具有限公司是一家集模具设计、制造、产品注塑加工于一体的企业，公司主要制造汽车车灯，保险杠，仪表台模具，汽车拉手模具，汽车内饰件，电视机，空调，冰箱，洗衣机，垃圾桶，塑料椅等日用品塑料模具及气辅模具。

New box design with durable 0.5 inch (13 mm) paving skin Vertically-adjusting mold mount for precise leveling of mold to machine Telescoping end sections with 12 inches (305 mm) of width variation on each side are available Standard paving depth is zero to 24 inches (610 mm)Edge slump adjustment Hydraulic Vertical Hinged Sideplates, self-contained inside the mold for track clearance Split, pressure-compensated sideplates Folding side plate wings for transporting without removing Pivoting mold mounting beam to eliminate stress points Self-supported TA is hydraulically driven with 3.5 inch (89 mm) ACME screws for up to a six inch (152 mm) crown Front and rear top T-bar on mold for attaching accessories and structural integrity Inserts are bolted together with front and rear alignment pins for easy mold assembly New vibrator mounting tube attaches to T-bar on mold – Vertical vibrator lift – Rear lubrication system with grease zerks accessible from the work bridge New strike-off – Mounted on paver frame T-rail, independent of the mold – New modular design with wedge lock system for ease in changing widths – 10 inches (254 mm) of hydraulic height adjustment – Hydraulic crown adjustment Spreader plow mounted to paver frame T-rail, optional auger available Tamper bar optional

与耐久性的新的箱子设计铺精密水准测量的0.5英寸(13 mm)皮肤垂直调整的模子登上模子用机器制造挤撞与12英寸(305 mm)的末端部分在每边的宽度变异是可利用的标准铺的深度是零对24英寸(610 mm)边缘暴跌调整水力垂直的取决于的Sideplates，独立性在轨道清除分裂的模子里面，折叠运输的pressure-compensated sideplates旁边板材翼没有去除在轴上旋转的模子架置射线消灭重音点Self-supported TA水力驾驶与3.5英寸(89 mm)由六英寸(152 mm)冠决定的尖端螺丝在前后冠上在模子的T酒吧附有的辅助部件并且结构正直插入物与容易的模子汇编新的振荡器架置管随员T酒吧的定位销一起在前后被闩上在模子–垂直的振荡器推力与油膏zerks的–后方润滑系统容易接近从新工作的桥梁触击–在摊铺机框架足迹，模子的独立登上了与楔子锁系统的–新的模块设计在改变的宽度的舒适的– 10英寸(254 mm)水力高低调整–水力冠调整分布器犁登上了对摊铺机框架足迹，任意任意木钻可利用的堵塞器的酒吧

Correctional checking formula of melt flow ratio in injection molding was obtained by introducing a correction coefficient β which reflected the complexity degree of mold cavity. The results show that, the maximum flow ratio of 486 can be obtained when injection pressure ranges from 150 MPa to 160 MPa in Archimedes spiral mold for PP, while maximum flow ratio of 419 can be obtained when injection pressure ranges from 160 MPa to 170 MPa for PE. There is a local fluctuation phenomenon for flow ratio and corresponding injection rate in square spiral mold when injection pressure of 100, 120 and 150 MPa for PP and 130, 140 MPa for PE are reached respectively,and this phenomenon is more serious for good fluidity of melt. The average flow ratio in Archimedes spiral mold is 6% larger than that in square spiral mold for PP, and 4% for PE, the average flow ratio of PP is 19% bigger than PE in Archimedes spiral mold, and 15% in square spiral mold. The influence of the cavity profiles on the melt flow ratio is more significant for good fluidity of melt.

研究结果表明：在阿基米德螺旋线模具中，PP在注射压力为150~160 MPa时取得最大流动比485，PE在注射压力为160~170 MPa时取得最大流动比419；在方形螺旋线模具中，PP在注射压力为100，120和150 MPa，PE在注射压力为130和140 MPa时流动比及所对应的注射速率出现波动，且流动性好的熔体波动更为严重；PP在阿基米德螺旋线模具中的流动比均值较其在方形螺旋线模具中大6%，而PE大4%；在阿基米德螺旋线模具中流动比均值PP比PE的流动比均值大19%，而在方形螺旋线模具中PP的流动比均值比PE的大15%；流动性好的熔体受模具型腔轮廓特征影响大。

与chill mold相关的网络解释 [注：此内容来源于网络，仅供参考]

chill mold：冷硬用铸模

loose detail mold 活零件模具 | chill mold 冷硬用铸模 | loose mold 活动式模具

chill mold：冷硬模

冷硬麻口控制法 chill mottle control | 冷硬模 chill mold | 冷硬深度 chill depth

chill mold：冷硬用铸

loose detail mold 活零件具 | chill mold 冷硬用铸 | loose mold 活动式具

chill mold：冷硬铸型

chill casting 冷硬铸造;冷硬铸件 | chill mold 冷硬铸型 | chilled roll 冷硬轧辊

metallic pattern chill mold：金属模

金属块,起熔块(低周波感应电炉) slug | 金属模 metallic pattern chill mold | 金属模,压铸模,刚模 die