cape chisel

cape chisel的基本解释

-

[机] 起槽凿

与cape chisel相关的网络例句 [注：此内容来源于网络，仅供参考]

Basanite and tephrite from Mt. Crater, Cape Bird and Bonney Lake exhibit similar composition in major elements and trace elements, rare earth elements . They are enriched in MgO, TiO〓, transitional elements and compatible elements , and depleted in SiO〓, Al〓O〓, Na〓O, K〓O, incompatible elements and rare earth elements; Latite from Cape Rodeys and Cape Evens are different from basanite and tephrite, they are enriched in SiO〓, Al〓O〓, Na〓O, K〓O, incompatible elements and rare earth elements, and depleted in Mgo, TiO〓, transitional elements and compatible elements. Volcanic rocks in five regions have the same isotopic ratio of 〓Sr/〓Sr (0.703115-0.703334) and 〓Nd/〓 Nd (0.512892-0.513076), however,〓Pb/〓Pb ratio in volanic rocks from Mt. Crater, Cape Bird and Bonney Lake is lower than those of Cape Rodeys and Cape Evens.

在主元素氧化物和微量元素、稀土元素含量上，克雷克特山、鸟角和博尼湖南岸的碧玄岩、碱玄岩成分比较类似，均具有较高的MgO、TiO〓、过渡元素和相容元素，较低的SiO〓、Al〓O〓、K〓O、Na〓O、不相容元素和稀土元素；罗德角和伊万思角安粗岩雷同，它们具有较高的SiO〓、Al〓O〓、Na〓O、K〓O、稀土元素和不相容元素，较低的MgO、TiO〓、过渡元素和相容元素，但五地区火山岩几乎具有一致的Sr、Nd同位素比值，〓Sr/〓Sr＝0.703115-0.703344、〓Nd/〓Nd＝0.512892-0.513076，在Pb同位素比值上，五地区的〓Pb/〓Pb＝18.664-19.913，其中碧玄岩和碱玄岩比安粗岩的比值稍低。

Pass to count to Wisterch parameter , and the steel wire is different from the molding tool get in touch with the length, and settle the path the research taking the length work the stabber angle to get under differently pull to stir the term, mold core adoption of best severally why size, combine the best work stabber of research the Cape, and settle the path to take the length nextly steel wire is in the molding tool of have fever to measure, air inside dispel-heat calories, winding dispel-heat on the coil-canister , and its molding tool dispel-heat calories of, and cause the steel wire the temperature difference pass in and outing the molding tool to influence steel wire machine function, under the experiment inside pull to stir the term according to the same race different work stabber Cape half of adoption the Cape(7 degree,10 degree,12 degrees, the best mold Cape, experience mold Cape) settle the path to take the length(2-3 mm,3-4 mm,4-5 mms, theories length, experience length) to proceed to experiment, and get the conclusion, work stabber the Cape then is more big the steel wire get in touch with the length with

通过对Wisterch参数，钢丝与模具接触长度、定径带长度、工作锥角度的研究得到了在不同拉拨条件下模芯采用的最佳几何尺寸，并研究最佳工作锥角、定径带长度下钢丝在模具中的发热量、空气中散热量、卷筒上的散热量及其模具散热量的不同，导致钢丝进出模具的温度差别对钢丝机械性能的影响，在实验中根据同种拉拨条件下采用不同工作锥角半角、定径带长度进行试验，得出结论，工作锥角越大则钢丝与模具接触长度越短，钢丝变形越剧烈，在模具中发热量就越高，导致钢丝出模温度高，使钢丝强度、硬度升高，弯曲、扭转次数降低，并且降低模具使用寿命。在其它条件相同的情况下，定径带越长则钢丝与定径带简壁磨擦增大，使钢丝发热量加大，从而使钢丝强度、硬度略升高，弯曲扭转次数略降低但定径带的增大减小了钢丝变形产生的弹性后效使钢丝出模直径比较稳定。

Chisel set, Carving chisel, Wood chisel, Firmer chisel,Cold

雕花木凿，雕刻刀，木工凿，车木刀，石工凿，起钉器

与cape chisel相关的网络解释 [注：此内容来源于网络，仅供参考]

Cape chisel：扁尖凿

Capacity of tank 油箱容量 | Cape chisel 扁尖凿 | Cap nut 盖螺母

Cape chisel：拐角凿子

cape bolt 固定螺栓 | cape chisel 拐角凿子 | Cape First 南非洲一级马海毛

Cape chisel：起槽凿

"capacity test","容量试验" | "cape chisel","起槽凿" | "capillarity","毛细管现象"

Cape chisel：扁尖凿, 削凿

Cape buffalo | 产于南非之黑色大水牛 | cape chisel | 扁尖凿, 削凿 | Cape Colored | 欧非混血的南非人

carpenter''''s cape chisel：木工岬錾

carpenter''''s bench knife 木匠木凳刀 | carpenter''''s cape chisel 木工岬錾 | carpenter''''s chipping-off chisel 木工平錾