bushing ['buʃiŋ]

bushing的基本解释

-

[变形] bush的现在分词

n.

轴衬, 套管

与bushing相关的网络例句 [注：此内容来源于网络，仅供参考]

Results indicate that radial distance of the bushing from the rotor center and the radius of the hemispherical bushing significantly affect wear rate,and minimzing both two values will result in lowest wear for micro-rotor systems in MEMS.However,it is noted that the bearing radius sets a lower limit on the hemispherical bushing radius since the bushings are located beyond the rotor inner radius.It is desirable to reduce their effects on friction and wear on micro-rotors by regulating the radius of the bushing and the radial distance of the bushing from the rotor center within permissive range of micro-fabrication.Severe wear exists with increasing applied load and rotating speed of the rotor.Stress distributions in the contact region are different from Hertz solutions due to the convergence stresses apearing on the uncontinuous curvature line and the contact pressures display symmetrical parabola in the contact region.

结果表明：在MEMS微转子系统中，微转子轴衬偏心距离和转子轴衬半径影响线磨损率，以两者减至最小为较理想，但须注意设计中轴承半径的限制，并使轴衬偏心距离大于轴承内半径；在转子加工制造许可的范围内，可以通过调整转子轴衬的半径和偏心距离来减少摩擦磨损对微电机的影响，随着转子所承受载荷和转子旋转速度的增加，其磨损严重；接触区的应力分布不同于经典Hertz解，这是由于应力集中出现在不连续的曲率线上，且接触区的接触压力呈现轴对称抛物线状分布。

A forming die set, comprising: an extendable punch having a first impact surface comprising a plurality of piercing points; a die body containing an aperture adapted to receive said punch; a fixed opposing post having a second impact surface positioned within said aperture, said opposing post recessed below a surface of said die body; at least one forming bushing slideably engaging said opposing post and positioned between said opposing post and said die body; and at least one forming bushing actuator supporting said at least one forming bushing.

形成一钢模组，包含：一个可扩充的打洞器让一种第一种冲击升至水面包含一个刺骨点的多数；一个包含一个孔的一钢模身体适应接受说打洞器；有一个第二个冲击表面的固定反对职位放置在说的孔里面，说反对被在一个说的一钢模身体的表面下面作凹处的职位；至少一个形成桥衬可滑动动人说反对职位而且在说反对职位之间放置而且说一钢模身体而且至少一个支援的形成桥衬主动器至少说一个形成桥衬。

It is indicated that the dielectric loss factor of the epoxy resin impregnated paper insulating bushing is generally higher than thatof the oil impregnated paper insulating bushing of the same voltage level; the tests should be strengthened when notable variation is found in the insulation dielectric loss factor and capacitance; when the variation is greater than 10%,the bushing must be replaced.

最后指出，环氧浸纸绝缘套管的介质损耗因数普遍高于同等电压等级的油浸纸绝缘套管，当发现绝缘介质损耗因数和电容值发生较明显变化时，应加大测试密度，当变化量大于10%时，必须更换套管。

与bushing相关的网络解释 [注：此内容来源于网络，仅供参考]

bushing：衬套

所有导销(GUIDE PIN),衬套(BUSHING)必须在尾端有凸型. 4. 所有模具设计图面纸张尺寸需统一使用全开规格尺寸,并等核准后,才开始制作. 5. 模具上成品部分加工时,应以成品图中尺寸公差的半值来做为加工公差,不得使用成品图上之公差来加工.

bushing：套管

电容型设备是重要的输变电设备,主要包括电流互感器(CT)、套管(Bushing)、耦合电容器(OY)、电容式电压互感器(CVT)等,在变电站中不仅数量多且具有重要地位,

bushing：轴衬

利用烧结铜合金(Sintered Copper Alloy)制成,粉末冶金得到的材料加工制成的轴承(bearing)与轴衬(bushing)将可以自行润滑、

bushing：絕緣套管

4.检查A-PB Bus 各断路器绝缘套管(bushing)头与汇流排间之接触电5.检查B-PB Bus 各断路器绝缘套管(bushing)头与汇流排间之接触电在无厂用海水(NSCW)支援下,起动空转一段时间,且 B 台紧急柴交换器(TBHX)冷却水,

bushing block：衬套

spring-box eject-plate弹簧箱顶板 | bushing block衬套 | insert 入块