bridge construction
- bridge construction的基本解释
-
-
桥梁(建造)工程
- 更多网络例句与bridge construction相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The method of control calculation of Suspension bridge and the design of SBCS (Suspension Bridge construction Control analysis System) is mainly analyzed in this paper.
本文主要研究了悬索桥施工控制方法及施工控制分析计算软件SBCS(Suspension Bridge construction Control analysis System)。
-
The superstructure uses the standard drawing, the substructure has used the gravity T-shape abutment and the rectangular buttress, in the design carries on the size to the abutment and the bridge pier to draw up, simultaneously satisfies the design the principle, the abutment uses 9.3m, in satisfies the structure and under the operation requirements premise, the abutment uses 9.3m to be long, because the geological condition decided, the pillar body uses 12m to be high, the open excavation foundation, the process load computation and the load combination, has carried on the bridge abutment and the pillar bottom section stress separately to the abutment and the bridge pier examines calculated, examines calculated the result conforms to the standard requirement, the bridge span uses the straight line build, and established this bridge construction organization plan, including the engineering project characteristic, the construction plan, the job practice, the bridge building construction technology, the measure has drawn up the top cap and the tray structure and matches the muscle chart, finally has drawn up Shui Xigou the bridge overall and the horizontal plan.
上部结构采用标准图，下部结构采用了重力式T 形桥台和矩形桥墩，设计中对桥台和桥墩进行了尺寸拟定，在满足构造和使用要求的前提下，桥台采用9.3m长，由于地质条件决定，墩身采用12m高，明挖基础，经过荷载计算和荷载组合，对桥台和桥墩分别进行了台底和墩底截面应力的检算，检算结果符合规范要求，桥跨采用直线布设，并且编制了该桥的施工组织设计，其中有工程项目的特征、施工方案、施工方法、桥梁工程施工技术，措施绘制了顶帽及托盘构造及配筋图，最后绘制了水溪沟大桥的总体及平面图。
-
The superstructure uses the standard drawing, the substructure has used the gravity T-shape abutment and the rectangular buttress, in the design carries on the size to the abutment and the bridge pier to draw up, simultaneously satisfies the design the principle, the abutment uses 9.3m, in satisfies the structure and under the operation requirements premise, the abutment uses 9.3m to be long, because the geological condition decided, the pillar body uses 12m to be high, the open excavation foundation, the process load computation and the load combination, has carried on the bridge abutment and the pillar bottom section stress separately to the abutment and the bridge pier examines calculated, examines calculated the result conforms to the standard requirement, the bridge span uses the straight line build, and established this bridge construction organization plan, including the engineering project characteristic, the construction plan, the job practice, the bridge building construction technology, the measure has drawn up the top cap and the tray structure and matches the muscle chart, finally has drawn up Shui Xigou the bridge overall and the horizontal plan.
内昆铁路水溪沟大桥，中心里程为DK608+393.00，该桥的设计方案有三个，通过技术、经济比较，采用4×32m预应力混凝土简支梁桥方案，桥梁全长149.5m，I级单线铁路，设计时速为120km/h，设计荷载为中活载。上部结构采用标准图，下部结构采用了重力式T 形桥台和矩形桥墩，设计中对桥台和桥墩进行了尺寸拟定，在满足构造和使用要求的前提下，桥台采用9.3m长，由于地质条件决定，墩身采用12m高，明挖基础，经过荷载计算和荷载组合，对桥台和桥墩分别进行了台底和墩底截面应力的检算，检算结果符合规范要求，桥跨采用直线布设，并且编制了该桥的施工组织设计，其中有工程项目的特征、施工方案、施工方法、桥梁工程施工技术，措施绘制了顶帽及托盘构造及配筋图，最后绘制了水溪沟大桥的总体及平面图。
- 更多网络解释与bridge construction相关的网络解释 [注：此内容来源于网络，仅供参考]
-
building construction general contractor：建筑施工总承包商
桥梁施工主管bridge construction superintendent | 建筑施工总承包商building construction general contractor | 建筑施工主管building construction superintendent
-
unsufficient span of bridge：桥梁孔径不足
桥梁建筑限界|bridge construction clearance, bridge structure gauge | 桥梁孔径不足|unsufficient span of bridge | 桥梁挠度|deflection of bridge span
-
Bridge Size Culverts Design Guidelines：桥梁大小涵洞设计指南
4. Construction Guidelines 建设指南 | 5. Bridge Size Culverts Design Guidelines 桥梁大小涵洞设计指南 | 6. BRIDGE STRUCTURES DESIGN CRITERIA 桥梁结构设计标准