blowing cylinder

与blowing cylinder相关的网络例句 [注：此内容来源于网络，仅供参考]

Cylinder, the cylinder sets of radial a surplus deformation of the cylinder sets a great impact on the cylinder liner reduced radial a surplus amount to reduce the deformation of the cylinder sets, the top surface of the body decreases roughness, but it will increase the body on the plane cylinder only mouth the roughness ; Preload reduced cylinder head bolt deformation of the cylinder liner little effect, the body can reduce the top surface roughness and cylinder body on the plane I ended roughness; Shen appropriate reduced cylinder head bolt hole deep can reduce the deformation of the cylinder sets, but will cause the body and the top surface roughness on the cylinder body only I roughness increases Plane .

工作工况下，对于第2缸来说，气缸套径向过盈量对气缸套变形影响很大，减小气缸套径向过盈量，有利于减小气缸套的变形，减小机体顶面不平度，但会增大机体上缸套止口平面的不平度；减小缸盖螺栓预紧力对气缸套变形影响很小，可减小机体顶面不平度和机体上缸套止口平面的不平度；适当减小缸盖螺栓沉孔深可以减小气缸套的变形，但会造成机体顶面不平度和机体上缸套止口平面不平度的增大。

Caused by disc brake on the brake Wheel Cylinder could not return to places 4 possible: First, 5 foot brake valve exhaust port blocking, high-pressure gas instinct platoon atmosphere, caused by gas-liquid master cylinder of the spring could not return to place, resulting in the system move oil, brake disc brake Wheel Cylinder Piston top dead and could not return to places; second is to the disc brake master cylinder gas-liquid pipeline blockage, resulting in brake Cylinder piston can not return to place; third master cylinder of the gas-liquid Spring itself can not return to position, brake fluid under high pressure gas can not return Axial pump to gas-liquid master cylinder reservoir chamber, resulting in brake Cylinder piston can not return to places; Fourth Wheel Cylinder piston disc brake system, due to moving fluid dirty or rusty card dead and can not return to the piston position.

造成盘式制动器上的制动分泵不能回位有4种可能：一是脚制动阀5的排气口堵塞，高压气体本能排人大气，造成气液总泵的弹簧不能回位，导致制动油将盘式制动器的制动分泵活塞顶死而不能回位；二是气液总泵至盘式制动器的油管堵塞，造成制动分泵活塞不能回位；三是气液总泵的弹簧本身不能回位，制动液在高压气体作用下，不能回到气液总泵的储油室，从而造成制动分泵活塞不能回位；四是盘式制动器制动分泵活塞由于制动液太脏或活塞生锈卡死而不能回位。

Equipment: 2 meters in diameter has a film blowing machine Units 1, 1 m film blowing machine 2 Units, 800-type film blowing machine 2 Units, 600 Units 5 film blowing machine, film blowing machine 400 Units 8, self-styled pocket machine 2 Units , bubble machine BAG 3 Units, 1000-type computer high-speed 8-color printing press 1, 800 computer-based 6-color press 2 Units, 600 computer-based 6-color press 2 Units, 600 2-color presses 5 Units, 600 single - Units 6 color printing press, 800-type compound machine 2 Units, 600-type compound machine 2 Units, 600 Units 2 computer triangular closure .600 PC .600 scalding machine 10 Units self-sealing machine hot computer 2 Units, 600-type computer hot bubble bag machine 3 Units, 1000 Units 1 computer perm machine perm machine .800 PC .600 Units 1 type bag machine automatic hot computer 3 Units, 3 Units polypropylene film blowing machine, poly bag machine hot 20 Units, contraction Film Blown Machine 2 Units, hot shrink film machine 12 Units, demolition machine, in closing down the machines, machine, granulating machine, grinder of the Units 1, as well as other equipment and so on

拥有2米直径吹膜机1台，1米吹膜机2台，800型吹膜机2台，600型吹膜机5台，400型吹膜机8台，自封口袋机2台，气泡袋机3台，1000型电脑8色高速印刷机1台，800型电脑6色印刷机2台，600型电脑6色印刷机2台，600型2色印刷机5台，600型单色印刷机6台，800型复合机2台，600型复合机2台，600型电脑三边封2台。600型电脑烫机10台。600型自封口电脑烫机2台，600型电脑气泡袋烫机3台，1000型电脑烫机1台。800型电脑烫机1台。600型手提袋全自动电脑烫机3台，聚丙吹膜机3台，聚丙袋烫机20台，收缩膜吹膜机2台，收缩膜烫机12台，拆边机，中封机，分切机，造粒机，粉碎机各一台，还有其它设备等等

与blowing cylinder相关的网络解释 [注：此内容来源于网络，仅供参考]

single cylinder blowing engine：单缸鼓风机

single cut file 单锉纹 | single cylinder blowing engine 单缸鼓风机 | single cylinder compressor 单缸压缩机