back liner

back liner的基本解释

-

书脊烫印机

与back liner相关的网络例句 [注：此内容来源于网络，仅供参考]

Pull back the wheelhouse liner and remove the bolts attaching the end cap to the front fender.

拉下舵手室外套，拆去连接末端端盖到前挡泥板的螺栓。

Complete coupon on back of tray liner, stick Game Piece on the coupon and deposit the coupon in the official entry box in the Restaurant.

把餐盘衬纸背后的优待券填好，奖游戏片粘贴在券上，然后设入店里的正式抽奖箱。

The assembly of journal and plain bearing liner space is too little, force of organic still oil pressure is small it is the crucial index that affects lubricant result, make lubricate because of lacking engine oil between crankshaft and plain bearing liner and bite dead invalidation, include to be pulled badly, lack lube, layer of alloy of dry attrition generation is fused, grind sliding surface to did not maintain the oily film of certain ply, and all sorts of local overload exhaustion are destroyed, cavitation erosion and V form are destroyed etc, through technology of him director diesel locomotive old experience reachs the analysis of pair of its breakdown reasons, put forward precautionary measures especially. As a result of,the burns caustic mechanism plain bearing liner to burn caustic mechanism of 1 plain bearing liner is the lube film burst between journal and plain bearing liner, cause plain bearing liner and crankshaft generation clash, below high temperature, high pressure and high rotate speed, the wear-resisting alloy layer of plain bearing liner wears away prematurely or fuse, cause plain bearing liner and crankshaft to stick thereby bite, can make the steel back of plain bearing liner and Kong Zhong produces whirligig, inlet port is jammed, carry on the back by steel again with the friction of aperture causes high temperature to make plain bearing liner burned-out further, can cause bolt to break off, happen swing a malign accident that pounds cylinder body of bad internal-combustion engine.

轴颈和轴瓦的装配间隙太小，还有机油压力低是影响润滑效果的关键指标，使得曲轴和轴瓦之间因缺少机油润滑而咬死失效，包括严重拉伤，缺少润滑油，干摩擦产生合金层熔化，磨滑面没有保持一定厚度的油膜，以及各种局部过载疲惫破坏，气蚀和V形破坏等，通过本人主管内燃机车技术多年经验及对其故障原因的分析，特提出预防办法。1轴瓦的烧损机理轴瓦烧损的机理是由于轴颈和轴瓦之间的润滑油膜破裂，导致轴瓦和曲轴产生摩擦，在高温、高压和高转速下，轴瓦的耐磨合金层过早地磨损或熔化，从而引起轴瓦和曲轴粘咬，会使轴瓦的钢背和座孔中产生旋转运动，进油孔被堵塞，再由钢背和座孔的磨擦进一步引起高温使轴瓦烧坏，并会造成螺栓折断，发生甩出捣坏内燃机缸体的恶性事故。

与back liner相关的网络解释 [注：此内容来源于网络，仅供参考]

back liner：中文:装背衬,装背衬机

中文:装订材料binding meterial | 中文:装背衬,装背衬机back liner | 中文:装版台lockup table

back liner：纸板芯层,纸板衬里

dryer:烘缸 | back liner:纸板芯层,纸板衬里 | back side:传动侧,传动面

back liner：书脊烫印机

back line ==> 家畜背线 | back liner ==> 书脊烫印机 | back lining ==> 背衬,腔背

back liner：纸板芯层,纸板衬层

batch type hydrapulper:间歇式水力碎浆机 | back liner:纸板芯层,纸板衬层 | back side:传动侧,传动面

book back liner：(书本)封面衬里

bonnet valve 帽状阀 | book back liner (书本)封面衬里 | bood back liner basis 书本标准规格