aspect ratio

aspect ratio的基本解释

-

纵横比, 高宽比

与aspect ratio相关的网络例句 [注：此内容来源于网络，仅供参考]

Studied the solid particles cyclone separation under structural parameters and operating parameters of different hydrocyclone, the results showed that major factor influence split ratio is in the ratio of entrance to exit pressure of hydrocyclone. Exit pressure has a certain influence on the split ratio, the various of the diameter and cone angle of hydrocyclone (in the ratio of entrance to exit pressure is constant) have no influence on split ratio; With diameter and cone angle increase, the separation granularity gradually increasing and recovery ratio decreasing; With entrance pressure increase, the separation granularity of hydrocyclone decrease, the split ratio of underset will increase slowly; With the diameter of overflow pipe increase, the separation granularity of hydrocyclone increasing and recovery ratio decreasing; With the diameter of underset pipe increasing, the separation granularity of hydrocyclone decreasing and recovery ratio increasing.

在不同的水力旋流器结构参数和操作参数下，对固体颗粒的旋流分离进行了分析研究，结果表明：旋流器的排出口比是影响分流比的主要因素，进口压力对分流比有一定影响，水力旋流器的直径变化和锥段角度变化对分流比基本上没有影响；随着直径、锥段角度的增大，分离粒度逐渐增大，回收率降低；随着入口压力增大，水力旋流器的分离粒度变小，底流的分流比会缓慢增加；随着溢流管管径的增加，分离粒度增大，分流比明显减小，回收率降低；随着底流管直径的增加，分离粒度减小，分级效果明显下降，回收率会增加。

Firstly, all the terms concerned are split up into basic term elements-termels, then eight aspects of quantificational indexes are given: errors-in-printing ratio,'inconsistent/uncanonical spelling' ratio,'unnecessary one-many/many-one correspondence' ratio,'inequivalent term' ratio,'discrepant interdisciplinary term' ratio,'unconformable-to-GB term' ratio,'incomplete/redundant term' ratio, and overall 'term worthy of revision/discussion' ratio.

其基本方法，一是从名词集中拆分出基础要素－名词元；二是提出八项量化指标：印误率，英语拼写不一致与不规范率，非必要的一多与多一对应率，英汉名词不对等率，与交叉学科名词有异率，与国标定名不符率，收词欠完备与冗余率及总体值得修榷率。

Correctional checking formula of melt flow ratio in injection molding was obtained by introducing a correction coefficient β which reflected the complexity degree of mold cavity. The results show that, the maximum flow ratio of 486 can be obtained when injection pressure ranges from 150 MPa to 160 MPa in Archimedes spiral mold for PP, while maximum flow ratio of 419 can be obtained when injection pressure ranges from 160 MPa to 170 MPa for PE. There is a local fluctuation phenomenon for flow ratio and corresponding injection rate in square spiral mold when injection pressure of 100, 120 and 150 MPa for PP and 130, 140 MPa for PE are reached respectively,and this phenomenon is more serious for good fluidity of melt. The average flow ratio in Archimedes spiral mold is 6% larger than that in square spiral mold for PP, and 4% for PE, the average flow ratio of PP is 19% bigger than PE in Archimedes spiral mold, and 15% in square spiral mold. The influence of the cavity profiles on the melt flow ratio is more significant for good fluidity of melt.

研究结果表明：在阿基米德螺旋线模具中，PP在注射压力为150~160 MPa时取得最大流动比485，PE在注射压力为160~170 MPa时取得最大流动比419；在方形螺旋线模具中，PP在注射压力为100，120和150 MPa，PE在注射压力为130和140 MPa时流动比及所对应的注射速率出现波动，且流动性好的熔体波动更为严重；PP在阿基米德螺旋线模具中的流动比均值较其在方形螺旋线模具中大6%，而PE大4%；在阿基米德螺旋线模具中流动比均值PP比PE的流动比均值大19%，而在方形螺旋线模具中PP的流动比均值比PE的大15%；流动性好的熔体受模具型腔轮廓特征影响大。

与aspect ratio相关的网络解释 [注：此内容来源于网络，仅供参考]

Aspect Ratio：纵横比

虽然在一般曼哈顿绕线架构下,纵横比(aspect ratio)不会影响放置器的好坏评断标准(),但在X架构下,纵横比却大大影响了放置结果的好坏. 在纵横比为0的情况下,代表着没有使用任何对角绕线,也就是说线长没有任何的改善;而若在纵横比为1的情况下,

Aspect Ratio：长宽比

传统电视(绿)与常见的电影画面长宽比例之102长宽比(aspect ratio)是用来描述视频画面与画面102的比例. 传统的电视萤幕长宽比为4:3(1.33:

Aspect Ratio：展弦比

P.45,同上凯利以[[F-104星式战斗机]]为蓝本,把那对低[[展弦比]](aspect ratio)的机翼换成一对类似滑翔机的超修长机翼,凯利以[[F-104星式战斗机]]为蓝本,把那对低[[展弦比]](aspect ratio)的机翼换成一对类似滑翔机的超修长机翼,

Aspect Ratio：画面比例

r)2 x画面比例(Aspect Ratio)转换器2 x影像解调器(Video Trans coder)2 x标志插入器(Logo Inserter)多种转换(Conversion)和扫描(Scaling)功能集於一身所有的影像输入皆具备同步锁定(Genlock)功能可放大(Zooming)画面中的某个区域到1000%,

Lock Aspect Ratio：锁定长宽比

单击"锁定长宽比"(Lock aspect ratio) 以保持基准平面的高度和宽度的比例. 单击"属性"(Properties) 选项页. 用户可以:双击要编辑的内部基准平面. 或者,选取要编辑的内部基准平面,右键单击,然后选取"编辑定义"(Edit Definition),