annular tubes

annular tubes的基本解释

-

[化] 套管

与annular tubes相关的网络例句 [注：此内容来源于网络，仅供参考]

In different conditions on fluidized state and stability of conical fluidized bed. The conlusions are: the conical angel of the conical fluidized bed is 20°, the fluidized state havesmall difference in conical distributor and distributor plate. The angle of conical bed increase,the fluidized state will have big difference. The angle is 60°and the conical as distributor, themass of fluidized is less, the most of material is the bottom of conical bed. The effect ofdistributor plate is much better than the conical distributor. Sawdust and rice hull can fluidize.The annular gap of conical distributor different, the angle of conical bed is same, the fluidizedquality of 10mm annular gap is better than the other conical distributors. The annular gap ismore wide, the conical bed have more slugging phenomenon and the pressure fluctuate is turnbig.In the experiment the flow of 2％and 4％distributor plates don\'t easy to control, becausethe pressure is very big and the pressure fluctuate of conical bed is too big.

在不同的条件下对锥形床的流化状态和稳定性进行了研究，结果得出：锥形床的锥角为20度时，分布锥和分布板的流化状态相差不明显，随着锥形床锥角的增大，分布锥和分布板的流化现象会出现明显的变化，锥形床锥角越大，分布锥的流化状态变化越明显，流化的的物料越少，大量物料都聚集在锥形床底部，而分布板在加料量少的情况下，能流化起来。10mm、15mm和20mm环隙分布锥在锥形床锥角相同条件下，10mm环隙分布锥的流化质量要好于其它两个分布锥，环隙越大越容易出现腾涌现象的产生，压降波动范围增大。2％、4％和6％开孔率分布板在本实验测定时，2％和4％开孔率分布板的流量不容易调节，同时产生的压降波动范围也很大，比较来说，6％开孔率分布板流化质量好些。

It is worth to be noted that the needed driving current to the MR valve with both annular and radial damping gaps is less than that to the MR valve with annular damping gaps under the cut-off state of the MR valves, which show that the MR valve with both annular and radial damping gaps consumes less energy.

测试结果显示：（1）在相同的工作条件下，同时具有圆环和圆盘阻尼间隙的磁流变阀产生的压降更明显；（2）处于截止状态时，同时具有圆环和圆盘阻尼间隙的磁流变阀的激励电流明显小于具有圆环阻尼间隙的磁流变阀的激励电流，因此采用同时具有圆环和圆盘阻尼间隙的磁流变阀可以节约能量的消耗。

The mechanical property testing shows that the seamless PLLA tubes perform excellent radial strength,which indicates that the mechanical properties of biodegradable stents made of these tubes was supposed to be excellent.PLLA and its composites were first used in preparing seamless tubes as antecedency of laser-cut biodegradable coronary stents in china.Finite element analyses of the biodegradable coronary stent model indicate the explorative design basically meets the requirement of reasonable and applicable stents.There is not such kind of research yet in domestic.Optimum laser-cuttting parameters of CO2 laser was cauculated based on experiential formula,within it,biodegradable coronary stents,especially those with complex structure would be manufacutured from seamless tubes quickly by laser microprocessing with high consistency to the design model.The processing efficiency of the CO2 laser demonstrated in experiential formula by us will play an important guiding role in manufacturing biodegradable stents by laser-processing.Our stents that ascribed to laser-cutted,slotted tube stent are proved to be biodegradable, self-expandable and good biocompatible,basically reach the international level on the aspest of manufacturing procedures and design.

研究结果表明：壳聚糖改性材料综合性能优于纯PLLA，更适合于作为可降解冠脉支架的原材料；自主设计的探索性自膨胀管状闭环型可降解冠脉支架的性能符合冠脉设计要求，设计、验证生物可降解冠脉支架模型的研究在国内还未见报道；制备的改性PLLA无缝管的力学性能优越，可通过激光切割获得冠脉支架，这是国内首次采用聚乳酸材料来制备通过激光加工出可降解冠脉支架的无缝管；二氧化碳激光器加工精度能达到加工要求，加工出来的血管支架名义设计与实测值误差小，实现了冠脉支架、尤其是带有复杂外观设计冠脉支架的快速化、规范化加工，对二氧化碳激光器加工聚乳酸材料的效果研究在国内外属于首创，获得的经验公式对日后的深入研究有重要的指导意义；制备的支架为激光切割管状闭环型冠脉支架，支架外观设计、支架加工手段、支架的性能都基本接近国际水平，支架样品符合设计的理念，可以实现自膨胀功能。

与annular tubes相关的网络解释 [注：此内容来源于网络，仅供参考]

annular air scoop：环形进气口

annular 环形,环形的,环形间隙,环状的,轮状 | annular air scoop 环形进气口 | annular amplifier 环形放大器

partial solar eclipse; an annular partial eclipse：日偏食

total solar eclipse ; an annular total eclipse 日全食 | partial solar eclipse; an annular partial eclipse 日偏食 | annular solar eclipse 日环食

annular spring：弹簧环

annular space 环形间隙 | annular spring 弹簧环 | annular valve 环状阀