annular knurl

annular knurl的基本解释

-

滚花

与annular knurl相关的网络例句 [注：此内容来源于网络，仅供参考]

In different conditions on fluidized state and stability of conical fluidized bed. The conlusions are: the conical angel of the conical fluidized bed is 20°, the fluidized state havesmall difference in conical distributor and distributor plate. The angle of conical bed increase,the fluidized state will have big difference. The angle is 60°and the conical as distributor, themass of fluidized is less, the most of material is the bottom of conical bed. The effect ofdistributor plate is much better than the conical distributor. Sawdust and rice hull can fluidize.The annular gap of conical distributor different, the angle of conical bed is same, the fluidizedquality of 10mm annular gap is better than the other conical distributors. The annular gap ismore wide, the conical bed have more slugging phenomenon and the pressure fluctuate is turnbig.In the experiment the flow of 2％and 4％distributor plates don\'t easy to control, becausethe pressure is very big and the pressure fluctuate of conical bed is too big.

在不同的条件下对锥形床的流化状态和稳定性进行了研究，结果得出：锥形床的锥角为20度时，分布锥和分布板的流化状态相差不明显，随着锥形床锥角的增大，分布锥和分布板的流化现象会出现明显的变化，锥形床锥角越大，分布锥的流化状态变化越明显，流化的的物料越少，大量物料都聚集在锥形床底部，而分布板在加料量少的情况下，能流化起来。10mm、15mm和20mm环隙分布锥在锥形床锥角相同条件下，10mm环隙分布锥的流化质量要好于其它两个分布锥，环隙越大越容易出现腾涌现象的产生，压降波动范围增大。2％、4％和6％开孔率分布板在本实验测定时，2％和4％开孔率分布板的流量不容易调节，同时产生的压降波动范围也很大，比较来说，6％开孔率分布板流化质量好些。

It is worth to be noted that the needed driving current to the MR valve with both annular and radial damping gaps is less than that to the MR valve with annular damping gaps under the cut-off state of the MR valves, which show that the MR valve with both annular and radial damping gaps consumes less energy.

测试结果显示：（1）在相同的工作条件下，同时具有圆环和圆盘阻尼间隙的磁流变阀产生的压降更明显；（2）处于截止状态时，同时具有圆环和圆盘阻尼间隙的磁流变阀的激励电流明显小于具有圆环阻尼间隙的磁流变阀的激励电流，因此采用同时具有圆环和圆盘阻尼间隙的磁流变阀可以节约能量的消耗。

The method of producing the pulley assembly may include modifying as by knurl (22 the outer flat circumferential surface of the metal insert prior to molding the plastic annular body about the metal insert, for clamping, structurally bonding, and resisting relative rotation between the plastic body and the metal insert.

生产滑轮组件的方法可以包括：在金属插入件周围模制塑料环形体之前，改变金属插入件的外圆周表面（例如通过压花（22）），以夹紧、在结构上连接及防止塑料体和金属插入件之间的相对转动。

与annular knurl相关的网络解释 [注：此内容来源于网络，仅供参考]

annular air scoop：环形进气口

annular 环形,环形的,环形间隙,环状的,轮状 | annular air scoop 环形进气口 | annular amplifier 环形放大器

partial solar eclipse; an annular partial eclipse：日偏食

total solar eclipse ; an annular total eclipse 日全食 | partial solar eclipse; an annular partial eclipse 日偏食 | annular solar eclipse 日环食

annular spring：弹簧环

annular space 环形间隙 | annular spring 弹簧环 | annular valve 环状阀