air inflating

air inflating的基本解释

-

打气

与air inflating相关的网络例句 [注：此内容来源于网络，仅供参考]

The static model of torsion joint is based on that of bending joint. The effects of structure parameters inside air pressure, initial angle, rube average radius, rube shell thickness on the turning angle are analyzed and the following conclusions are drawn: the relationship between the angle of torsion joint and the inside air pressure is basically linear, the angle of torsion joint increases with the initial angle and rube average radius, the angle of torsion joint decreases while the rube shell thickness increases. The kinetic equation is built for torsion joint. Simulating experiment implies that the time of inflating and deflating process is extremely shorter than that of kinetic process. So the pneumatic process can be ignored in actual system design and control. The factors that affect the dynamic features of torsion joint, such as shell thickness of rubber tube, average radius, initial angle, connector's outlet area, moment of inertia and viscous damping coefficient, are analyzed and the following conclusions are drawn: the change of rube shell thickness has no effects on the dynamic process of FPA inside air pressure while greatly affects the turning angle of torsion joint; when the rube shell thickness is small, the torsion joint has a bigger turning angle, no overshoot and long risetime, when the shell thickness is big, the turning angle of torsion joint is small, but has high response speed, overshoot and low shock; when the rube average radius increases, the turning angle of torsion joint increases and the overshoot increases too; when the initial angle of torsion joint is big, the turning joint is big, the overshoot is small and shock is low, but the risetime is big; the connector's outlet area affects the dynamic process of FPA inside air pressure greatly, but has no effects on the dynamic process of turning angle; moment of inertia and viscous damping coefficient have no effects on the dynamic process of FPA inside air pressure, but affect the dynamic process of turning angle greatly.

在弯曲关节模型推导的基础上，建立扭转关节的静态模型，并分析了扭转关节内腔压力，初始转角，橡胶管平均半径，橡胶管壁厚等参数对关节转角的影响，得出扭转关节的转动角度与充入FPA内腔的压缩气体压力之间基本呈线性关系，扭转关节的转角随初始角度和橡胶管平均半径的增大而增大，扭转关节的转角随橡胶管壁厚的增大而减小的结论；建立了扭转关节的动力学方程，仿真实验表明FPA的充放气过程与扭转关节的动力学过程相比时间极短，在实际系统设计和控制过程中可以忽略不计；分析讨论橡胶管壁厚，平均半径，初始角度，气体节流口面积，转动惯量，粘性阻尼系数等因素对扭转关节动态特性的影响，得出橡胶管初始壁厚的变化对扭转关节FPA内腔压力的动态响应几乎没有影响而对关节转角的响应曲线影响比较明显，壁厚较小时，关节可以得到较大的转角，并且转角的响应曲线没有超调，但上升时间长，壁厚较大时，关节转角变小，响应加快，但是有超调和轻微振荡现象，橡胶管平均半径越大，得到的关节转角越大，但是转角响应的超调量也随之增大，FPA的初始角度越大，关节的转角越大，并且超调量减小，振荡减弱，但是上升时间增大，管接头出口面积的大小对关节FPA内腔压力的建立过程影响较大，但对关节转角的动态响应几乎没有影响，转动惯量和粘性阻尼系数对FPA内腔压力的动态过程几乎没有影响而对扭转关节转角有较大影响等结论。

You should feel air flowing through the hose and hear it inflating the tire.

你应该感觉到空气流经软管和听到轮胎充气。

The air powered tiltable pillar and two pneumatic cylinders for wheel clamping GT express inflating system can inflate the inner tube of a tyre in an instant.

气动可倾斜立柱，双重气动机械锁定。 GT快速充气系统瞬间为无内胎轮胎进行快速充气。

与air inflating相关的网络解释 [注：此内容来源于网络，仅供参考]

air inflating：充气

空气湿度 air humidity? | 充气 air inflating? | 空气喷射柴油发动机 air injection diesel engine?

air inflating：轮胎打气

air infiltration 漏风 | air inflating 轮胎打气 | air injection 空气喷射

air inflating：轮胎打气, 充气

air infiltration 漏风, 漏气 | air inflating 轮胎打气, 充气 | air injection 空气喷射