adsorption compound

adsorption compound的基本解释

-

[机] 吸附化合物

与adsorption compound相关的网络例句 [注：此内容来源于网络，仅供参考]

Its high-capacity and strong-acid-resistance were proved. In the acid condition, the adsorption efficiency to acide green 6B and direct fast yellow RL reached above 90%. Through the adsorption rate curve on adsorption behavior of the three dyes, they were all according with pseudo-secondary adsorption rate curve. The rate constant of adsorption increased with increasing temperature. Through the adsorption isotherm of the three dyes, acide green 6B and direct fast yellow RL were according with Langmuir equation, while disperse blue 56 was according with Freundlich equation. The adsorption behavior was an endothermic process. Entropy was increasing during the adsorption. So raising temperature was in favor of adsorption.

结果表明，甲醛环氧氯丙烷交联壳聚糖对染料具有较强的吸附性能和耐酸性能，在酸性条件下，对酸性绿6B和直接耐晒黄RL的吸附效率达90％以上；拟合甲醛环氧氯丙烷交联壳聚糖对三种染料的吸附速率曲线，发现该吸附行为符合拟二级吸附速率曲线，其吸附速率常数随温度的升高而增大；通过测定不同温度下甲醛环氧氯丙烷交联壳聚糖吸附三种染料的吸附等温线表明，甲醛环氧氯丙烷交联壳聚糖对酸性绿6B和直接耐晒黄RL的吸附符合Langmuir方程，而对分散蓝56的吸附符合Freundlich方程，甲醛环氧氯丙烷交联壳聚糖对染料的吸附是一个吸热过程，吸附后体系熵增加，升温有利于吸附。

By contrasted with silica gel, the corn hull desiccants by hydrolyzation method and heat treatment method have advantages as stabilization on moisture adsorption, less water of reversible adsorption and high moisture adsorption ratio in high humidity. These desiccants have disadvantages as lower moisture ratio than silica gel in low humidity and slower moisture adsorption speed than silica gel. The corn hull desiccant by derivation method has advantages as high moisture adsorption ratio, high moisture adsorption speed, stabilization on moisture adsorption and hardly any water of reversible adsorption.

通过与变色硅胶干燥剂的对比，通过水解法和热处理法得到的玉米渣皮干燥剂的优点是吸水稳定，可逆吸附水少，在高湿度下吸水率高，不足是在较低的湿度下，吸水率比变色硅胶干燥剂略低，吸水速度比硅胶慢；通过衍生方法得到的玉米渣皮干燥剂的优点是吸水率高，吸水速度快，吸湿稳定持久，几乎不含可逆吸附水，不足是再生后产品容易结块。

This paper presented the research and exploration of mechanism and technics as well as the design of the magnetic circuit of this new compound machining, based on above, establishing the parameter model, meantime, analyzing influential effects on productivity of magnetic and EDM compound machining the holes through large numbers of experiments, including velcoity contrast experiments of pre-compound and after-compound machining with the change of current, velcoity contrast experiments of pre-compound and after-compound machining with the change of magnetic induction, velcoity contrast experiments of pre-compound and after-compound machining with the change of impulse width, experiments of the superficial roughness, experiments of the Electrode wastage, and intersectant experiments analysis as well as the change experiments of current waveforms. Through a number of experiments we analysed the influential effects of magnetic and EDM compound machining, compared the factors with EDM by oneself. A large of experiment records and deducibility have demonstrated that the productivity of magnetic and EDM compound machining is developed by 20%～400% than traditional EDM.

本论文对磁场电火花复合加工这种新的复合加工的机理、工艺和复合加工的磁路设计进行了研究和探索，在此基础上，建立了磁场电火花复合加工的参数模型，同时通过大量的随着电流变化磁场电火花复合前后加工速度对比实验、磁感应强度变化时的加工速度变化实验、随脉冲宽度变化的加工速度实验、表面粗糙度实验、电极损耗量实验、磁场电火花复合加工正交实验分析、电流波形变化等实验，实验分析了影响磁场电火花小孔加工效率的因素，并且跟单一的电火花加工中的影响因数进行了比较，大量的实验数据和理论推导证明磁场电火花复合加工比传统的单一电火花加工的效率提高了20％～400％左右。

与adsorption compound相关的网络解释 [注：此内容来源于网络，仅供参考]

adsorption compound：吸附化合物

adsorption chromatography 吸附色层分析法 | adsorption compound 吸附化合物 | adsorption current 吸附电流