abscissa axis

abscissa axis的基本解释

-

横坐标轴, 横轴

与abscissa axis相关的网络例句 [注：此内容来源于网络，仅供参考]

In view of the general relationship between corporate income tax burden and scale of enterprises, in a rectangular coordinate system, suppose that ordinate axis stands for tax burden and abscissa axis stands for scale of enterprises, then the curve of tax burden of three cities' enterprises is like a flat S. that's to say, tax burden of the smallest enterprises is relatively high, that of enterprises scaled from 5 million to 10 million yuan is the lowest, and then tax burden increases with the scale going up. The trend continues until the scale of enterprises is beyond 100 million yuan and the top point appears. When the scale of enterprises expands to 800 million yuan, the tax burden starts to turn down and is lower than that when the scale of enterprises is beyond 100 million yuan.

就企业所得税负担与企业规模的一般关系看，如果以直角坐标系的纵轴表示税负，横轴表示企业规模，那么随着企业规模的变大，三城市企业的税负曲线呈一个平躺着的S形状，即规模最小的企业税负较高，500到1，000万元企业的税负率最低，然后企业的税负率开始随规模的增加而提高，这种趋势一直延续到企业规模超过1亿元时达到最高点，待企业规模继续扩张到8亿元左右时，税负开始回落，并将低于原先超过1亿元时的水平。

Result: For all of the 100 atlases samples, in 15 samples (15%) there were skew transverse processes in abscissa axis, in 5 samples (5%) asymmetry of anterior and posterior tubercles in longitudinal axis, in 10 samples (10%) asymmetry of left and right posterior arches of atlases, in 11 samples (11%) asymmetry of vertebral foramens.

结果：100例寰椎标本左右横突在横轴上偏歪者15例(15%)、前后结节在纵轴上不对称者5例(5%)、左右后弓不对称者10例(10%)、椎孔不对称者11例(11%)。

This article introduced the manipulator, it outputs four groups by PLC to actuate the abscissa axis, the z-axis, the chassis rotation, hand-rotating motor separately, and controls the manipulator abscissa axis and the z-axis pint pointing, the micro switch bequeaths the position signal to the PLC main engine; The electrical machinery drives the hand fingernail and the chassis revolve; The solenoid valve controls air valve the switch to control the manipulator hand fingernail to gather, then realizes the manipulator proper motion function.

本文介绍的机械手是由PLC输出四路来分别驱动横轴、竖轴、底盘转动、手转动电机，控制机械手横轴和竖轴的精确定位，微动开关将位置信号传给PLC主机；电机拖动手爪和底盘旋转；电磁阀控制气阀的开关来控制机械手手爪的张合，从而实现机械手精确运动的功能。

与abscissa axis相关的网络解释 [注：此内容来源于网络，仅供参考]

abscissa axis：横坐标轴

abscess 气孔;砂眼;脓肿 | abscissa axis 横坐标轴 | abscissa 横坐标

abscissa axis：横座标轴

abscissa 横坐标 | abscissa axis 横座标轴 | absence of collector 无集电环

abscissa axis：横座标轴

abscissa ==> 横坐标 | abscissa axis ==> 横座标轴 | absence of collector ==> 无集电环